Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Disconnect recovery
Options
N7BCP
Member ✭✭
For the most part, remote over wireless N has been working well. Occasionally, I'll have a radio disconnect during a QSO. Last night while in a JT65 contact I had a disconnect and once the radio was disconnected the JT65 serial link to the flex crashed. Upon restarting SSDR the radio shows red busy in the radio chooser. Until that disconnect the remote quality bars were full green. Maybe a spike in latency? Power off and on the radio and then I'm able to start SSDR but QSO is done by this time. I remember when PowerSDR would not recover from FireWire issues automatically and then finally with a new release the radio was able to recover on its own. I'd like to see some sort of retry logic hat would allow the radio and SSDR to re establish a connection automatically. Having the RX freeze momentarily would be better than a complete disconnect. Running 6500, SSDR 1.4.3 Mac book pro with 8gb ram windows 8.1 boot camp (not using virtualization). I'm about 15 meters from the access point. I don't doubt I will have the occasional long DPC or network blip, would just like to see a better user experience without the radio, SSDR, and CAT restart needed, especially during a contact. 73 Larry HB9EYQ
0
Comments
-
I have entered this report into our bug tracker for further investigation. Please report any additional information related to this specific issue in this community topic.
0
Leave a Comment
Categories
- All Categories
- 245 Community Topics
- 2.1K New Ideas
- 490 The Flea Market
- 7.4K Software
- 5.9K SmartSDR for Windows
- 135 SmartSDR for Maestro and M models
- 327 SmartSDR for Mac
- 243 SmartSDR for iOS
- 224 SmartSDR CAT
- 163 DAX
- 347 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 766 Maestro
- 42 FlexControl
- 836 FLEX Series (Legacy) Radios
- 727 Genius Products
- 392 Power Genius XL Amplifier
- 251 Tuner Genius XL
- 84 Antenna Genius
- 222 Shack Infrastructure
- 149 Networking
- 370 Remote Operation (SmartLink)
- 118 Contesting
- 582 Peripherals & Station Integration
- 116 Amateur Radio Interests
- 809 Third-Party Software