Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Won't transmit with 2.6.1
Options
Jim Shaffer
Member ✭✭
I'm using a third-party client to access my 6500, not SmartSDR. I updated my radio from 2.5.1 to the latest 2.6.1, and rebuilt my client with the associated FlexLib. Sometimes, if I run my client without having rebooted the radio, it just won't transmit. I'm using CW, and it won't transmit when closing the key or sending data via CWX.
Any thoughts?
Any thoughts?
0
Comments
-
I am using 2.6.1 with my radio at 2.6.1.
I'm still experiencing this issue, and need to solve it. If I disconnect my client from the radio, and then connect later, let's say after at least an hour, the radio won't transmit. It also won't even key at all. By this I mean that if breakin is not enabled, the normal behavior is to present a tone in the monitor when the key is pressed. That also doesn't happen in the case I describe.
0 -
This only occurs with CW, and all that is important is the level the radio is at, 2.6.1 or later. The work around is to keep the client connected to the radio, not acceptable for a remote situation. I have not seen any response from the folks at Flex. Apparently this is not something seen by anyone else, but is a serious situation in my opinion.0
Leave a Comment
Categories
- All Categories
- 246 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 163 DAX
- 348 SmartSDR API
- 8.6K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 765 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 733 Genius Products
- 393 Power Genius XL Amplifier
- 255 Tuner Genius XL
- 85 Antenna Genius
- 228 Shack Infrastructure
- 152 Networking
- 370 Remote Operation (SmartLink)
- 120 Contesting
- 583 Peripherals & Station Integration
- 115 Amateur Radio Interests
- 811 Third-Party Software