Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, and Tuner Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Why does CWU always revert back to CWL upon changing bands?
Charles - K5UA
Member ✭✭
When I select CWU under settings, it reverts back to CWL whenever I change bands. Is here a way to globally make CWU the default setting? This worked just fine in V1.3.8.
0
Answers
-
How are you changing bands?0
-
Good question....I'm using the K9DUR 6000 Memory program to change bands using buttons I created under v1.3.8. Also, it just dawned on me that I did not do a cold reboot after installing v1.4. Since I turn off all power every time I leave the shack, it will be a cold reboot when I get back out to the rig and I'll try again. Otherwise, I'll change bands the conventional way from the Flex panel and see if that retains the CWU selection across band changes.
Thanks Tim.
0 -
So here is what could be happening.
With SmartSDR v1.4, there was a change to support both the CWU (ZZMD04;) and CWL (ZZMD03;) CAT commands properly. Previously, entering either of the two aforementioned CAT commands to change the slice mode to CW would change the demodulation mode but it would not change the CW tuning mode. This resulted in CAT enabled programs that had CWU and CWL modes defined were not properly setting the state of the radio.
Now the appropriate ZZMD command will change the demod mode to CW and set the CW tuning mode (upper or lower) as well.
If the CAT enabled program is responsible for the change in the tuning mode, you need to contact the developer and let them know of this change so they can modify their programs.0 -
Much appreciated Tim. Thanks again!0
Leave a Comment
Categories
- All Categories
- 244 Community Topics
- 2.1K New Ideas
- 481 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 132 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 162 DAX
- 348 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 745 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 720 Genius Products
- 387 Power Genius XL Amplifier
- 249 Tuner Genius XL
- 84 Antenna Genius
- 225 Shack Infrastructure
- 150 Networking
- 366 Remote Operation (SmartLink)
- 120 Contesting
- 580 Peripherals & Station Integration
- 114 Amateur Radio Interests
- 805 Third-Party Software