Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
While tuning, hitting CW key will drop transmitter but radio stays at tune power
Options
Robert Cheek
Member
I got the rig in an odd mode the other day. I was in CW mode but only had a few watts output no matter where I put the RF Power slider. I discovered the Tune Pwr slider would control the power. Then I noticed the Tune button was still blue. Well, today I discovered how I got into that mode. I was in CW mode, clicked the Tune button to tune up the external antenna tuner and I bumped the paddle and the TX dropped. The rig would transmit but at Tune Pwr setting. The Tune button stays blue. I clicked the Tune button and all went back to normal.
Is this normal operation? I could not find this "feature" in the SW users manual I am using 1.9.7 version of SmartSDR.
Is this normal operation? I could not find this "feature" in the SW users manual I am using 1.9.7 version of SmartSDR.
0
Comments
-
Hello Robert.
I observed this 'feature' some time back and didn't report as it seemed not so important a 'use case'. Reverified this and it can be duplicated with Maestro as the control, in which case the tune LED stays red.
I'd say "best practice' is not to hit the bug when tuning (assuming one uses a bug for CW).
Best,
Tim0 -
It is not normal operation. This behavior has been entered into our bug tracker as issue #4166.0
-
The first time I saw this I think that I hit the keyer paddle by accident and didn't notice until I saw the power output was 5 watts. It was a bit confusing because I was calling a cw net and really needed full power!
Most of the electronic keyers I have that have a "tune" mode will drop the key line when the paddle is tapped. It would be nice if the Flex did the same thing. But I can't see where dropping the TX and staying in tune mode would be normal.
0 -
Thanks Tim. Not a big thing, but a surprise if you are not expecting it!
0
Leave a Comment
Categories
- All Categories
- 245 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.3K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 327 SmartSDR for Mac
- 241 SmartSDR for iOS
- 224 SmartSDR CAT
- 161 DAX
- 343 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 768 Maestro
- 42 FlexControl
- 836 FLEX Series (Legacy) Radios
- 726 Genius Products
- 391 Power Genius XL Amplifier
- 251 Tuner Genius XL
- 84 Antenna Genius
- 221 Shack Infrastructure
- 149 Networking
- 369 Remote Operation (SmartLink)
- 118 Contesting
- 582 Peripherals & Station Integration
- 116 Amateur Radio Interests
- 809 Third-Party Software