Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, and Tuner Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
VAC, Flex1500 and CWGET?
Ken Broome
Member ✭✭
How do I hook up cwget to flex1500 without a "Line In" input on my windows 10 Dell?
0
Answers
-
Hello,
you must open a new serial port, go to:
setup> dsp> keyer and make the settings with the new serial port
1 -
Ken,
I am not sure you got your answer yet.. Normally the audio is passed from PowerSDR using a small sound driver called VAC , just like if you were using a digital SW package mentioned in the Users Guide , like FLDigi or HRD. You can use the audio from the headphone jack to the sound card input, DCE or program to program method is more efficient.
You can purchase VAC (Virtual Audio Cable ) version 4.14 via this link. http://software.muzychenko.net/eng/vac.htm
Hope this help answer your question..
1 -
Thanks Dudley, I downloaded the VAC414, full version, then the video on how to install the VAC by third part on youtube, but I can't get the number of cable box to go past 3. The video at https://www.youtube.com/watch?v=ON5G4IIx6j8 @ 3:51 indicates I need to set the number of cables at 4, and I can't figure a way to set it higher than 3. Since the video instruction is based on the 4 setting, I'm stuck. Please advise configuration with my FLEX1500. Thanks in advance for yours and others help in this matter!
Ken
0 -
Ken, as it says in the video, you need 2 VAC cables, not 4 (in the
video 4 cables are recommendet for a second receiver only)
This tutorial is very good:
http://kc.flexradio.com/KnowledgebaseArticle50230.aspx
Alex0
Leave a Comment
Categories
- All Categories
- 244 Community Topics
- 2.1K New Ideas
- 481 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 132 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 162 DAX
- 348 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 746 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 722 Genius Products
- 388 Power Genius XL Amplifier
- 250 Tuner Genius XL
- 84 Antenna Genius
- 225 Shack Infrastructure
- 150 Networking
- 366 Remote Operation (SmartLink)
- 120 Contesting
- 580 Peripherals & Station Integration
- 114 Amateur Radio Interests
- 805 Third-Party Software