Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, and Tuner Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
v2.2.8 will not update. Error message - unable to connect to the radio
Joe
Member
Flex 6300 error. Downloaded v2.2.8. SmartSDR Icon opens showing name and callsign. I click on yellow update on bottom of icon. Software times out and say radio connection failed.
0
Answers
-
If you have been using your radio normally it should be connecting. But you could do a cold restart by shutting down the radio, disconnect the power cable, wait 20 seconds then reconnect and re start the radio, the up grade should continue
0 -
Is this over SmartLink?0
-
It's also OK to turn off your radio, then, turn off your power supply (using the power supply switch) wait a few seconds, turn your power supply back on, then turn on your Flex. Sometimes it can be a pain to remove the power cable from the radio.0
-
Updated my network to Medicom. DOnt know if it has something to do with port forwarding I dont know how to set that up0
-
Joe, you leave out information, is this a new install? Have you used this radio before?
How is it connected to you computer?
Are you trying remote?
In most cases routers work with Flex radios right out of the box, and nothing to configure. But some routers are odd balls.
So for anyone to help we need to know your setup.0 -
Bill I have had the radio for 2 years with no issues. Its always been connected to the computer through a 4 port netgear switch 1g. Recently changed from ATT to Mediacom. Medicom comes up with a message about port forwarding. I didnt have anything set with ATT not sure what I am suppose to do about Mediacom.0
-
Ok, that's good info, Michael Walker is very good with this as some others as well. I am afraid of steering you the wrong way.0
-
Michael I have changed my ISP since I last used my radio. I dont understand the port setup now my old router was pnp. Thanks0
Leave a Comment
Categories
- All Categories
- 244 Community Topics
- 2.1K New Ideas
- 481 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 132 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 162 DAX
- 348 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 746 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 722 Genius Products
- 388 Power Genius XL Amplifier
- 250 Tuner Genius XL
- 84 Antenna Genius
- 225 Shack Infrastructure
- 150 Networking
- 366 Remote Operation (SmartLink)
- 120 Contesting
- 580 Peripherals & Station Integration
- 114 Amateur Radio Interests
- 805 Third-Party Software