Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Upgrade to SSDR v2 and 6500 - lock up!
Options
Steve Bunting
Member ✭✭
Hi Everyone,
I have collected a 6500 from an estate sale and immediately upgraded to SSDR v2.0.19 via an ethernet cable. The radio is available in the SSDR Launch panel but clicking on it causes the SSDR to hang. No number of radio or PC reboots can make it work.
SSDR on the same PC works just fine with my 6300 with direct connection, over the LAN or via Smartlink. I assume that this is a problem with the 6500? What so I do next?
Thanks
Steve, M0BPQ
I have collected a 6500 from an estate sale and immediately upgraded to SSDR v2.0.19 via an ethernet cable. The radio is available in the SSDR Launch panel but clicking on it causes the SSDR to hang. No number of radio or PC reboots can make it work.
SSDR on the same PC works just fine with my 6300 with direct connection, over the LAN or via Smartlink. I assume that this is a problem with the 6500? What so I do next?
Thanks
Steve, M0BPQ
0
Comments
-
I am using a Flex 6500 and have never seen this problem, ever. I sounds like a disconnection problem.0
-
Check the version of firmware that is already in the radio , in the Radio Chooser window of SmartSDR v2 , move your cursor over the radio , if earlier than version 1.4, go to version 1.4 , other wise try going to version 1.11.12 first and then you should be able to make the upgrade, and don't load DAX and SmartCAT..
0 -
Mine is v2.1.32.104 is that the latest?0
-
yes it is , and don't forget to do the cold boot of the radio after the update, this can cause some lockups if you don't.
73,
Dudley
1 -
Thanks for replies. All my SW versions match so that wasn't the problem
Dudley is spot on here - a hard reset fixed it! Thanks so much.
Next to sort out the unresponsive Maestro.....
73
Steve, M0BPQ0 -
Steve, If you got ythe Maestro from the same estate sale, and it has been unplugged for a couple Months, then you may need to send it to your local Service Center to have the internal battery replaced.
0
Leave a Comment
Categories
- All Categories
- 245 Community Topics
- 2.1K New Ideas
- 490 The Flea Market
- 7.4K Software
- 5.9K SmartSDR for Windows
- 135 SmartSDR for Maestro and M models
- 327 SmartSDR for Mac
- 243 SmartSDR for iOS
- 224 SmartSDR CAT
- 163 DAX
- 347 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 768 Maestro
- 42 FlexControl
- 836 FLEX Series (Legacy) Radios
- 727 Genius Products
- 392 Power Genius XL Amplifier
- 251 Tuner Genius XL
- 84 Antenna Genius
- 222 Shack Infrastructure
- 149 Networking
- 370 Remote Operation (SmartLink)
- 118 Contesting
- 582 Peripherals & Station Integration
- 116 Amateur Radio Interests
- 811 Third-Party Software