TX Power Meter QRP Scale...

  • 6
  • Idea
  • Updated 2 months ago
SSDR is so easy to use with low-power digital modes, wouldn’t it be great to have a 0-to-10 Watt scale for the RF Power meter for QRP use?  Maybe even an auto-expand feature that would automatically switch to the lower scale below, say, 12 watts (and a color/increment change to indicate the low-power scale)?  With an opt-out for those who want the scale to stay as-is, of course.

Photo of Jim, KJ3P

Jim, KJ3P

  • 88 Posts
  • 12 Reply Likes

Posted 4 years ago

  • 6
Photo of DrTeeth

DrTeeth

  • 1687 Posts
  • 387 Reply Likes
I'd like to see greater granularity below 40W a) for digimodes and b) the UK has a 32W limit 1850-2000KHz.

Would also be useful for those not on full licences with limited permitted power.

Merry Christmas and Happy New Year.
(Edited)
Photo of Al / NN4ZZ

Al / NN4ZZ

  • 1735 Posts
  • 590 Reply Likes
Jim,
Take a look and see if this is would address what are looking for.  The snapshot below is from an idea to expand the scale, make it easier to read and also provide a digital readout.  It has 24 votes so far.  More info at this link. 

https://community.flexradio.com/flexradio/topics/idea_to_improve_the_swr_and_power_scale_readability

Regards, Al / NN4ZZ  
al (at) nn4zz (dot) com


Photo of Larry Loen  WO7R

Larry Loen WO7R

  • 204 Posts
  • 23 Reply Likes
Even given it is a percentage and not an absolute value (it is actually fairly close even as they promise it is not exact), it would still be a good thing to switch scales when the "percentage" is in the bottom 5 or 10 "percent" range.
Photo of Mark Erbaugh

Mark Erbaugh

  • 395 Posts
  • 34 Reply Likes
Another solution would be to add another setting in the GUI that set the 100% point on the power slider.  My old icom 703 had and adjustable max power setting in a setup menu (10w, 5w, 2.5w, 1w, 0.5w as I recall).
Photo of DrTeeth

DrTeeth

  • 1687 Posts
  • 387 Reply Likes
My max power is slightly different on each band, not by much, but enough for the power slider to be inaccurate. I normally use 30% on the power slider for JT65 work - there is approx 5-10 W difference between my 'best' band and the 'worst'. That difference is greater at 100%. I'd rather have an accurate power meter than % slider.
(Edited)
Photo of Larry Loen  WO7R

Larry Loen WO7R

  • 204 Posts
  • 23 Reply Likes
But what if you are doing true QRP with JT65?  It arises two ways.  1. Naturally, in the obvious way you expect.  2.  Feeding an amplifier at low total power.  I find it a very nice thing to "buffer" the rig through an amplifier at all times.  And, JT9, in particular, is a high duty cycle mode (nearly key down in practice), so even asking a 500 watt amp to put out 20 or 30 watts is a lot of load (and a load I like to move it from the rig to the amp when I can).  1 watt on the Flex drives 20 or 30 on my Alpha and 10 or 20 on my "brick" amp.
Photo of Jim, KJ3P

Jim, KJ3P

  • 88 Posts
  • 12 Reply Likes

Asking a 100-watt transceiver to accurately go down to well under five watts may not be practical.  A better way is to run the rig at, say, an easier-to-measure five watts, then use an RF pad to get down to a watt or less.  Such pads are used all the time in broadcast transmitters to a) run the exciter at a constant level, and b) smooth out any slight mismatches between the exciter and the amplifier input.

 By the way, I use JT9 frequently at five watts (and sometimes 10 to 15 watts for QRO!), and the fan on my 6300 never changes. The 6300 is rated at 100 watts for RTTY, so I’m not the least bit concerned with running 10 or 15 watts.

 And I do like Mark’s setpoint idea for output power levels.  Switching to a 10-watt 100% point certainly could switch the scale at the same time, doing away with my questionable “auto” scale switching idea.  The engineering folks could also use this to address any transmitter non-linearities at lower levels.


Photo of Joe N3HEE

Joe N3HEE

  • 145 Posts
  • 21 Reply Likes
I would also like to see an auto scaling watt meter.