Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Transverter transmit profile is changing
Options
Joel N9LQ
Member ✭✭
Hi, I am a new 6600 user and overall I am thrilled with it. However, I am having an issue that I need some help with. I have set up, and connected a transverter for 70cm which seems to be working ok generally. I have set up a transmit profile for 70cm, with the power slider at 50%, the tune slider at 25%, and both rx and tx on xverter B. I have created a global profile using this xmit profile. All is fine to this point. However, when I reload the global profile, the power slider goes to 100%. The xmit profile name doesn't change. Am I missing something. Thanks!
0
Answers
-
The first thing I think of is if you have made any changes to the transmit profile after you have saved your global profile with that transmit profile you must resave the global profile again so it will use the latest changes in the transmit profile. I said this without verifying with the manual where the xvtr power settings are stored.0
-
Thanks for the idea, but I have made sure to resave the global profile after editing the transmit profile, so that's not it unfortunately.
One other clue, that may not be correct because it happens very fast. It looks like when I load the global profile, it loads the xmit profile correctly, but then the power slider changes to 100% immediately.
0 -
This is a known issue has been logged as defect #6222
0 -
Power output changes with a 2 meter transverter when I change frequency?? I set the power slider to 100 and then on the transverter page I set power to equal 10 watts with the slider at 100. When I change to another nearby frequency the power output changes?? I wonder if this is a defect or am I missing something??0
Leave a Comment
Categories
- All Categories
- 245 Community Topics
- 2.1K New Ideas
- 490 The Flea Market
- 7.4K Software
- 5.9K SmartSDR for Windows
- 135 SmartSDR for Maestro and M models
- 327 SmartSDR for Mac
- 243 SmartSDR for iOS
- 224 SmartSDR CAT
- 163 DAX
- 347 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 768 Maestro
- 42 FlexControl
- 836 FLEX Series (Legacy) Radios
- 727 Genius Products
- 392 Power Genius XL Amplifier
- 251 Tuner Genius XL
- 84 Antenna Genius
- 222 Shack Infrastructure
- 149 Networking
- 370 Remote Operation (SmartLink)
- 118 Contesting
- 582 Peripherals & Station Integration
- 116 Amateur Radio Interests
- 811 Third-Party Software