Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, and Tuner Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Thank you Tim!
JohnSweeney
Member ✭✭
I opened a ticket regarding the use of the REM ON jack. Within a couple hours I had a complete and thorough reply from Tim. Not many places will respond so quickly and thoroughly. Thank you Tim! I asked if I was doing any harm by grounding the REM ON jack continuously and simply turning the 12V supply on and off to remotely control the radio. Tim said no problem. Just for fun, I timed my boot up time with the REM ON jack shorted and not shorted. Exact same boot up time - 54 seconds. This saves adding a remote relay to control the REM ON jack.
1
Comments
-
Another advantage is that I have found sometimes I lose my ability to communicate with Smartlink and by powering off the rig and back on again solves the problem. Not sure why. Perhaps this kills two birds with one stone.
Jim, K6QE
1 -
In my remote base situation, I turn the power supply off and on with a remote IP switch. I have to do this every week or so when my radio 'disappears'. I recently had a situation where the remote IP switch was unreachable so I couldn't reboot the radio. I was able to get someone to cycle the main breaker to the shack (often not possible since my shack is hard to get to in the winter) and everything came back up normally. I'm going to add a 'remote on' switch as a layer of redundancy for rebooting the radio.0
-
Tim is the best customer advocate I have ever met. He honestly believes that is his job and works so hard to deliver.
Thanks Tim for such great service to our community!3
Leave a Comment
Categories
- All Categories
- 244 Community Topics
- 2.1K New Ideas
- 481 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 132 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 162 DAX
- 348 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 747 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 722 Genius Products
- 388 Power Genius XL Amplifier
- 250 Tuner Genius XL
- 84 Antenna Genius
- 225 Shack Infrastructure
- 150 Networking
- 366 Remote Operation (SmartLink)
- 120 Contesting
- 580 Peripherals & Station Integration
- 114 Amateur Radio Interests
- 805 Third-Party Software