Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, and Tuner Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Squelch-induced noise?
Keith Ferguson
Member
I've just noticed what may be a problem on my 6500 running 1.4.3. I've been using it on 70MHz FM, and for a while it's seemed to me that signals are too noisy for their received signal strength - ie the receiver isn't being quieted as much as I'd expect.
What I've just discovered is that the effect varies with the squelch threshold setting. If the squelch threshold is set below the point where it's always open, the receiver seems to behave pretty much as I'd expect. Once the squelch control is advanced past the point where it would mute the receiver if no signal is being received, the noise in the receiver increases as you raise the squelch threshold, even if a signal that you'd expect to fully quiet the receiver is present.
I haven't hauled out my signal generator to investigate further yet, but I wondered if anybody else has noticed, or can reproduce this effect (or tell me what I'm doing wrong)?
What I've just discovered is that the effect varies with the squelch threshold setting. If the squelch threshold is set below the point where it's always open, the receiver seems to behave pretty much as I'd expect. Once the squelch control is advanced past the point where it would mute the receiver if no signal is being received, the noise in the receiver increases as you raise the squelch threshold, even if a signal that you'd expect to fully quiet the receiver is present.
I haven't hauled out my signal generator to investigate further yet, but I wondered if anybody else has noticed, or can reproduce this effect (or tell me what I'm doing wrong)?
0
Answers
-
I just tested this on 6m FM and I am not experiencing the same issue. I'm using a 6700.
0
Leave a Comment
Categories
- All Categories
- 244 Community Topics
- 2.1K New Ideas
- 481 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 132 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 162 DAX
- 348 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 745 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 720 Genius Products
- 387 Power Genius XL Amplifier
- 249 Tuner Genius XL
- 84 Antenna Genius
- 225 Shack Infrastructure
- 150 Networking
- 366 Remote Operation (SmartLink)
- 120 Contesting
- 580 Peripherals & Station Integration
- 114 Amateur Radio Interests
- 805 Third-Party Software