Sneak Peak of Smartlink

  • 4
  • Praise
  • Updated 1 year ago

Thanks Tim! This gets me more prepared for the upcoming release. Interesting date on the cover page...

Jim

ka7gzr

Photo of ka7gzr

ka7gzr

  • 215 Posts
  • 36 Reply Likes

Posted 1 year ago

  • 4
Photo of Ria - N2RJ

Ria - N2RJ, Elmer

  • 2263 Posts
  • 891 Reply Likes
Might be a good time to make sure your router can handle it. Otherwise, it's almost go time :)
Photo of Michael Aust

Michael Aust

  • 135 Posts
  • 32 Reply Likes

Tim,

  Like that answer for V2.0, looking for that slight edge when speeds

get slower on the Rural Fringes of Slug Slow DSL Internet Providers.

73 Mike


(Edited)
Photo of Ria - N2RJ

Ria - N2RJ, Elmer

  • 2263 Posts
  • 891 Reply Likes
The real advantage of smartlink is zero configuration. Just create an account, pair and go. It is also the only way to get maestro connected remotely without another vpn client box.

You can also allow others to use your radio without giving access to the whole network and without a bunch of messy firewall rules.

For me though, it's a small piece of the puzzle. I am looking forward to the other improvements that it brings later such as multi client.

Ria
Photo of Michael Aust

Michael Aust

  • 135 Posts
  • 32 Reply Likes
Ria & Michael

Have slow DSL here with a BufferBloat from dslreports with an F grade.

Will the IQrouter help?

With a Single Panadapter, everything minimum, can run SoftEther 
VPN, with RasPi at home, but audio stutters sometimes at remote location 
Starbucks (coffee shop) Wi-Fi

Hoping V2 helps a little as well, using 1.9.13 here SSDR

My dslreport below

(Edited)
Photo of Mack McCormick

Mack McCormick, Elmer

  • 318 Posts
  • 115 Reply Likes
The IQRouter will help a little with buffer bloat but the fundamental issue are your speeds. Is there any other provider you can use that offers better speeds?

Mack
W4AX
Alpha Team
Photo of Tim - W4TME

Tim - W4TME, Customer Experience Manager

  • 9152 Posts
  • 3471 Reply Likes
As Mack said it will help some.  I suspect your experience with the VPN running remotely will be about the same as when using SmartLink.  Having at least 1 mbps up is the recommended minimum upload bandwidth for an adequate user experience.  You can do it with less, as you have noted, but also as Mack said, it is a bandwidth issue too.

One thing to point out is the "saw tooth" pattern on your uploads.  That is indicative of your ISP doing bandwidth throttling on your upload bandwidth.  So there is capacity, you may be able to have your ISP provide some more upload bandwidth.
Photo of Jeffrey Kerber, N3VE

Jeffrey Kerber, N3VE

  • 118 Posts
  • 18 Reply Likes

It has been a long time coming, release 2.x please.

Jeff

Photo of Richard McClelland, AA5S

Richard McClelland, AA5S

  • 275 Posts
  • 52 Reply Likes
I notice that Tim purged all references to the Flex 6800/6800M in this document :-) 
Photo of NX6D Dave

NX6D Dave

  • 302 Posts
  • 89 Reply Likes
Assuming you meant 6400 or 6600, nothing was purged.  None of the user documentation, other than announcements and flyers, has been updated with the new model numbers.

These How To guides have been written from the point of view of existing radios in the field.  When the newer models begin to ship an appropriate general overhaul of the documentation will take place. The new models will be added to the documentation, no models will be removed.
(Edited)
Photo of KF4HR

KF4HR

  • 521 Posts
  • 147 Reply Likes
First I've heard of the 6800M, but doesn't surprise me.  I'm guessing my 6700 will be  weeping resale value soon.
(Edited)
Photo of Ria - N2RJ

Ria - N2RJ, Elmer

  • 2263 Posts
  • 891 Reply Likes
It's a joke. I don't think such a creature exists yet.
Photo of KF4HR

KF4HR

  • 521 Posts
  • 147 Reply Likes
A 6800M would make sense.  Two slices available on its internal display, and 8 slices available on an external display.  Include in the improved Contest Filters, two transverter ports, HDMI port(s), and keep VHF.  
Photo of Jay Spaulding

Jay Spaulding

  • 65 Posts
  • 3 Reply Likes
They said it was going to be out in June... Just didnt say what year. 
Is there an update on that?
Photo of David Decoons wo2x

David Decoons wo2x, Elmer

  • 1185 Posts
  • 242 Reply Likes
Since the Quick Start Guides are out it is getting very close :-)
Photo of K1UO - Larry

K1UO - Larry

  • 790 Posts
  • 126 Reply Likes
Maybe Monday as that will match the date on the recently released Documents.   ;~)
Photo of Mike - VE3CKO

Mike - VE3CKO, Elmer

  • 352 Posts
  • 133 Reply Likes
Makes sense Larry, and to answer Jays' question above, the year is 2017 Jay.
Photo of Jay Spaulding

Jay Spaulding

  • 65 Posts
  • 3 Reply Likes
I was told June at Dayton. And it's passed. Just wondering.

So we have it June 2017 gotcha.
Photo of Steve - N4TTY

Steve - N4TTY

  • 85 Posts
  • 10 Reply Likes
Was that a misprint where it said you wouldn't have to buy a license if you purchased your radio after May 2007? Was it supposed to be May 2017?
Photo of David Decoons wo2x

David Decoons wo2x, Elmer

  • 1185 Posts
  • 242 Reply Likes
After May 19, 2017
Photo of Tim - W4TME

Tim - W4TME, Customer Experience Manager

  • 9152 Posts
  • 3471 Reply Likes
It's a typo.  the year is 2017.  We'll get it fixed
Photo of ka7gzr

ka7gzr

  • 215 Posts
  • 36 Reply Likes

My experience with Softether VPN with a Pi has been hit and miss with remote WiFi connections. I have tested with about 15 WAN WiFis and have had about 20% success rate. I can always connect with my AT&T cellular service. I have played with the Waterfall rates and other parameters that eat up bandwidth and they do help the quality of the experience.

Jim

ka7gzr

Photo of Ria - N2RJ

Ria - N2RJ, Elmer

  • 2263 Posts
  • 891 Reply Likes
I haven't had such a problem. I'm able to connect everywhere where ports aren't heavily restricted.
Photo of Rick  WN2C

Rick WN2C

  • 272 Posts
  • 32 Reply Likes
The Gurus at Flex looked into their crystal ball when they were figuring out when Vers 2 was going to be released and the crystal ball said Ju, but they couldn't see it cleary. So it it must have been July not June they were seeing.
Photo of VE7ATJ

VE7ATJ

  • 121 Posts
  • 22 Reply Likes
The one thing I noticed missing from the documentation provided was any sort of description of how to hook up the radio to use Smartlink from a hardware PoV (i.e. what cables go from what jacks to where).  I know this may seem obvious to a majority of us here, but for newbies, there is no hint/nor diagram of how to hook things up.  Is this going to be in another doc?  It would make sense (to me at least) to have a 'how to connect your radio for SmartLink" section at the beginning of the doc, with a diagram.
Photo of David Decoons wo2x

David Decoons wo2x, Elmer

  • 1185 Posts
  • 242 Reply Likes
You do not forward physical ports on the router. Ports in this case refer to TCP protocol.

Look at the model of your router and search online if it supports uPNP. If it does then no port forwarding needs to be done.

Dave wo2x
Photo of NX6D Dave

NX6D Dave

  • 302 Posts
  • 89 Reply Likes
Confusion of terms unfortunately.  We're talking about this https://en.wikipedia.org/wiki/Port_forwarding and this https://en.wikipedia.org/wiki/Firewall_pinhole.

None of this will be an issue for users whose local router/firewall supports Universal Plug N Play (UPnP).  
Photo of Ria - N2RJ

Ria - N2RJ, Elmer

  • 2263 Posts
  • 891 Reply Likes
An easier way of saying all of this:

Plug in the radio straight to the router like you would do a Roku or other internet appliance then follow the quick start guide for SmartLink to enable the radio's remote capability. This is really all you need to do for most consumer routers in the default, out of box configuration.

Unless your radio is connected directly to your computer, it should have been set up this way already.

If you're having problems, look in your router documentation for instructions to enable UPnP.  For most people that would fix most SmartLink issues. 

Of course, you're more than welcome to ask questions here... but I think for most this should be easy pickings.

Ria
(Edited)
Photo of VE7ATJ

VE7ATJ

  • 121 Posts
  • 22 Reply Likes
Thanks, Ria... but for the complete newbie, we need to be even MORE precise as in "Connect an Ethernet cable from the LAN socket on the back of the radio to an available socket on your router. Then, you may either connect your PC directly to the router using a similar cable and available port on the router, or you may connect your PC to the radio using a wireless connection."  << and include a diagram >>.  BTW, my router has 2G and 5G capability.  I'm assuming 5G would be better?
Photo of Tim - W4TME

Tim - W4TME, Customer Experience Manager

  • 9152 Posts
  • 3471 Reply Likes
BTW, my router has 2G and 5G capability.  I'm assuming 5G would be better?

Maybe.  5G has higher throughput but is more susceptible to signal attenuation due to things like walls.