Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, and Tuner Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Smartlink mic audio failling
Joel Lobão
Member ✭✭
Hi,
I'm having a problem with audio in the SSDR. I'm remote and i'm using the flex 6300 with an SPE 1k-FA. The problem is that the mic fails sometimes. I tried differente headsets and with another PC but the problem continue. The radio go to TX mode but without modulation. I hear my audio in the monitor. I tried with recorded audio with N1MM+ and DAX and the audio didn't failed.
Any thoughts?
I had to stop the ARRL DX because of this
73 de CT1HXB - Joel
I'm having a problem with audio in the SSDR. I'm remote and i'm using the flex 6300 with an SPE 1k-FA. The problem is that the mic fails sometimes. I tried differente headsets and with another PC but the problem continue. The radio go to TX mode but without modulation. I hear my audio in the monitor. I tried with recorded audio with N1MM+ and DAX and the audio didn't failed.
Any thoughts?
I had to stop the ARRL DX because of this
73 de CT1HXB - Joel
0
Comments
-
Joel, try it without running the amp and let me know. You can shut the amp key off in the settings under TX band settings, un check the band you are using, See if your problem goes away.0
-
Hi, I done that but still failing sometimes.0
-
Joel
You said this is with SmartLink. Are your operating remotely?
Mike
0 -
Hi Mike, Yes, I'm operating remote. The network is ok. I have fiber 100mbs in the radio side and 200mbs in the remote side. 80ms ping, no packet loss. Jitter 1ms 73 de CT1HXB - Joel0
-
Hi Joel
I doubt it is the radio, but something in your path is failing. There are many parts that you do not have control over. High speed internet is great for streaming movies, but when it comes to HF communications the connection is much more critical. When was the last time the radio was rebooted?
What are your bufferbloat numbers? (http://www.dslreports.com/speedtest) Given your speeds, it should be A+, but don't be surprised if it isn't. I would run this test on a computer on the same LAN as the radio and on the remote operators LAN.
Is there any WiFi involved, possibly on the operator end? If so, can you test without it?
I hope that helps a bit, Mike
0
Leave a Comment
Categories
- All Categories
- 244 Community Topics
- 2.1K New Ideas
- 481 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 132 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 162 DAX
- 348 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 745 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 722 Genius Products
- 388 Power Genius XL Amplifier
- 250 Tuner Genius XL
- 84 Antenna Genius
- 225 Shack Infrastructure
- 150 Networking
- 366 Remote Operation (SmartLink)
- 120 Contesting
- 580 Peripherals & Station Integration
- 114 Amateur Radio Interests
- 805 Third-Party Software