Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
SDR Bridge 1.5 will not connect to radio
Options
Bob KN4HH
Member ✭✭
I have been using SDR Bridge v1.3 with no problem. I uninstalled v1.3 and installed v1.5. When I execute 1.5, CW Skimmer comes up and eventually SDR Bridge comes up and says "not connected to radio". The Slice and Stream boxes are gray. I checked the setup and it agrees with my 1.3 settings with the exception of the new features. I insured that DAX IQ channels are active and assigned to SDR Bridge. I am not listing this as a problem since I usually suffer from a short between the headset, hi hi.
0
Answers
-
No changes were made to the SDR-Bridge code that connects to the radio, and v1.5 is built with the latest version v1.6.21 of FlexLib. I'm not sure where the problem might be.
Check to make sure SSDR, CAT, and DAX are all connected to the radio. Then start SDR-Bridge. If there is still a problem, try restarting the radio.
73 Ed W2RF
0 -
Ed, I knew it had to be something simple. My network was blocking SDR Bridge from communicating with the Flex. Interestingly, it did not block 1.3. All is working well now. Many thanks for your reply and for providing such a wonderful piece of software.
73, Bob, KN4HH
1 -
Hi Bob,
Just curious about network issue that was blocking SDR-Bridge. I might add some notes about it to the next version of the quickstart guide.
Did you get an error message?
What version of windows are you running?
What did you do to fix the issue.
Regards, Al / NN4ZZ
al (at) nn4zz (dot) com
6700 - HW.................... V 1.6.21.77
SSDR / DAX / CAT...... V 1.6.21.159
Win10
0 -
Ed, I am running Windows 10. I received a message basically saying "a program (SDR Bridge) is trying to access the network". It provided options such as "Do not allow access to the network (Recommended), or "allow access".
Unfortunately, I do not remember any further context. Since no one else has reported this condition, hopefully this is an isolated case.
Bob, KN4HH
0
Leave a Comment
Categories
- All Categories
- 246 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 163 DAX
- 348 SmartSDR API
- 8.6K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 766 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 733 Genius Products
- 393 Power Genius XL Amplifier
- 255 Tuner Genius XL
- 85 Antenna Genius
- 229 Shack Infrastructure
- 153 Networking
- 370 Remote Operation (SmartLink)
- 120 Contesting
- 583 Peripherals & Station Integration
- 115 Amateur Radio Interests
- 813 Third-Party Software