Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.

Screen missing slice and info but showing signals

Dave Dave
Dave Dave Member ✭✭
edited December 2019 in FLEX-6000 Signature Series

Before 1.5 I never had this problem, happened a few times with 1.5 and now a few times with 1.5.1  Anyone ever had same problem? Once I restart all seems fine.

Sorry for the poor picture, I brightened it up as best as I could.

image

Comments

  • Burt Fisher
    Burt Fisher Member ✭✭
    edited August 2016
    You have a moonbounce function?
  • Jim Gilliam
    Jim Gilliam Member ✭✭
    edited October 2015
    which radio are you using?
  • RoyS
    RoyS Member ✭✭
    edited December 2019
    Dave,
    I too have the 6300. This happens to me when I calibrate using 10 Mhz instead of 15. When the software returns from the cal routine, it has lost where it was. I simply select another profile and the problem is gone until next cal.
  • Mike KD2CJJ
    Mike KD2CJJ Member ✭✭
    edited December 2019
    Me too!!! I put in a helpdesk ticket and the tech said I didn't have a slice open. I tried to expliain To him that this happened when I started the radio from a clean shutdown. It has never done it again and flex has no means to read error logs etc. Thus I told him to close the issue.

    Submit a helpdesk ticket...I will post who I spoke with when I get back to my personal pc Also a 6300 Is it me or 6300 seems to have more issues than the other units?
  • Steve K9ZW
    Steve K9ZW Member ✭✭✭
    edited March 2017

    What do you hear?

    Could it be that the panadapter is showing the sampling though no slice-receiver is active?

    If you create another slice-receiver is it a "B" (or should I say non-"A" slice-receiver)?

    I had some profile issues going between the 6700 and 6300 that mimicked this and they cleared by creating new profiles and doing a full reset.

    You might have something completely different though.

    73

    Steve K9ZW 

  • Mike KD2CJJ
    Mike KD2CJJ Member ✭✭
    edited March 2017
    Here is the image of my issue... As you can see it was still receiving but I lost all audio and all controls went blank.  The only way to fix this was to do a clear of the persistence db (complete reset to default of the radio)...  Looks the same to me as Daves issue.
    My helpdesk request number is Request #10817 if anyone wants to also reference this issue.  
    image
  • Steve K9ZW
    Steve K9ZW Member ✭✭✭
    edited November 2016

    Mike - when mine acted up the create slice-receiver was grayed-out, but yours looks clickable.


    Can you add one clicking?

    If yes, is it A or B or ??



    image


    Just a thought.


    73

    Steve K9ZW

  • Mike KD2CJJ
    Mike KD2CJJ Member ✭✭
    edited October 2015
    Tried that, double clicking and adding from the left, changing bands, etc. etc... nothing worked.
  • Tim - W4TME
    Tim - W4TME Administrator, FlexRadio Employee admin
    edited December 2016
    Mike and Roy - I have entered a bug report on the existing slice not being recreated after running the frequency calibration.
  • Tim - W4TME
    Tim - W4TME Administrator, FlexRadio Employee admin
    edited March 2017
    I have entered this report into our bug tracker for further investigation.  Please report any additional information related to this specific issue in this community topic.
  • Steve K9ZW
    Steve K9ZW Member ✭✭✭
    edited November 2016

    Expected you had - in my case they were also grayed out.

    Hope it gets resolved soon!

    73

    Steve K9ZW

  • RoyS
    RoyS Member ✭✭
    edited December 2016
    Tim, What appeared to be a bug on my 6300 was squashed by a factory reset. Recreation of slice works now.
  • Walt - KZ1F
    Walt - KZ1F Member ✭✭
    edited November 2016
    Steve asks a valid question, in a problem I reported about a year ago about no panadapter getting created, when a panadapter was finally created all slices could be instantiated, except that first one, A. So to test Steve's question, create a new panadapter and see if the first slice I'd B,not A.
  • Tim - W4TME
    Tim - W4TME Administrator, FlexRadio Employee admin
    edited December 2016
    If they are grayed out, you have orphaned slice/panadapter resources.  Rebooting the radio will release them. Using any third-party GUI apps that may not be cleaning up after themselves?
  • Tim - W4TME
    Tim - W4TME Administrator, FlexRadio Employee admin
    edited December 2016
    RRR.  Thanks for the update.

Leave a Comment

Rich Text Editor. To edit a paragraph's style, hit tab to get to the paragraph menu. From there you will be able to pick one style. Nothing defaults to paragraph. An inline formatting menu will show up when you select text. Hit tab to get into that menu. Some elements, such as rich link embeds, images, loading indicators, and error messages may get inserted into the editor. You may navigate to these using the arrow keys inside of the editor and delete them with the delete or backspace key.