Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, and Tuner Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Replies to Equalizer Info commands
Doug - K3TZR
Member
When I send an "eq rx info" command to the radio I receive the expected response:
SCCB288B6|eq rx mode=1 63Hz=10 125Hz=10 250Hz=10 500Hz=10 1000Hz=10 2000Hz=10 4000Hz=10 8000Hz=10
but I also receive the following:
SCCB288B6|eq rxsc mode=1 63Hz=0 125Hz=0 250Hz=0 500Hz=0 1000Hz=0 2000Hz=0 4000Hz=0 8000Hz=0
What is the significance of the "rxsc" reply? Similarly, two replies are received for the "eq tx info" command, one with "tx" and one with "txsc".
SCCB288B6|eq rx mode=1 63Hz=10 125Hz=10 250Hz=10 500Hz=10 1000Hz=10 2000Hz=10 4000Hz=10 8000Hz=10
but I also receive the following:
SCCB288B6|eq rxsc mode=1 63Hz=0 125Hz=0 250Hz=0 500Hz=0 1000Hz=0 2000Hz=0 4000Hz=0 8000Hz=0
What is the significance of the "rxsc" reply? Similarly, two replies are received for the "eq tx info" command, one with "tx" and one with "txsc".
0
Answers
-
When we first created the EQ it was implemented in our audio codec chip and the API commands and responses had a range of 0 to 20 for the EQ levels. In v1.4 we moved the location of the EQ into our DSP co-processor and it made more sense to use the actual values of the EQ which have a range from -10 to 10.
We did not want to break the API for developers that had already written EQ controls so we left the old API command which is "eq rx" and added a new command/status which is the "eq rxsc". Both commands and statuses are valid with the "eq rx" command using the old 0 to 20 range and the new "eq rxsc" command using the -10 to 10 range.
The same applies to the TX EQ.0 -
Thanks Ed,
I suspected something like that.
I'm primarily looking forward from 1.4 so when I see the "sc" form coming from the Radio I'll use the "sc" form when sending commands.
To afford some measure of backward compatibility, when I only see the non-"sc" form coming from the Radio, I'll use the non-"sc" form in commands I send to the Radio.0 -
Sounds like a good plan. That's very close to what we do in SmartSDR.0
Leave a Comment
Categories
- All Categories
- 244 Community Topics
- 2.1K New Ideas
- 481 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 132 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 162 DAX
- 348 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 746 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 722 Genius Products
- 388 Power Genius XL Amplifier
- 250 Tuner Genius XL
- 84 Antenna Genius
- 225 Shack Infrastructure
- 150 Networking
- 366 Remote Operation (SmartLink)
- 120 Contesting
- 580 Peripherals & Station Integration
- 114 Amateur Radio Interests
- 805 Third-Party Software