Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Problem Using DAX with Fldigi
Options
Gary Robertson - KY5R
Member ✭✭
By following Greg's video very carefully, I think I have SmartSDR 1.1 and Fldigi properly configured to have DAX interfaced with Fldigi. However, I cannot get any signal showing in the DAX Control panel (channel 1) and no signals show up in Fldigi even though the signal strength bar in Fldigi moves up and down. In SmartSDR, I have slice A set on 14.070 with DIGU selected, and both DAX controls set to Channel 1.
In the DAX Control Panel, I note that it does not reflect anything in the Slice area for Channel 1. That doesn't seem right. It should say Slice A.
In Fldigi, I have the following configuration:
Configure – Rig Control - Fldigi
In the DAX Control Panel, I note that it does not reflect anything in the Slice area for Channel 1. That doesn't seem right. It should say Slice A.
In Fldigi, I have the following configuration:
Configure – Rig Control - Fldigi
Use RIGCAT – make sure that box is checked
Use SmartSDR.xml file
Device - COM8
For PTT - I have COM6 established in SmartCAT
Retries - 3, Retry Interval - 50, Baud Rate - 19200, Write Delay - 25, Stopbits - 1
RTS/CTS - Flow Control is checked
CAT command for PTT is checked
Always Initialize and Save
Configure Audio - Fldigi
PortAudio is checked
Capture - DAX Audio RX 1
Playback - DAX Audio TX 1
Always Save
I am obviously doing something wrong. Any help would be appreciated in getting Fldigi to play well with SmartSDR 1.1 and DAX.
0
Answers
-
Found a solution in a past community post. Had to exit out of the DAX Control Panel and then restart DAX from the FlexRadio Systems/SmartSDR 1.1 folder. Everything is now working but this seems to be a continuing problem that needs to be addressed for DAX to be stable.0
Leave a Comment
Categories
- All Categories
- 245 Community Topics
- 2.1K New Ideas
- 490 The Flea Market
- 7.4K Software
- 5.9K SmartSDR for Windows
- 135 SmartSDR for Maestro and M models
- 327 SmartSDR for Mac
- 243 SmartSDR for iOS
- 224 SmartSDR CAT
- 163 DAX
- 347 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 766 Maestro
- 42 FlexControl
- 836 FLEX Series (Legacy) Radios
- 727 Genius Products
- 392 Power Genius XL Amplifier
- 251 Tuner Genius XL
- 84 Antenna Genius
- 222 Shack Infrastructure
- 149 Networking
- 370 Remote Operation (SmartLink)
- 118 Contesting
- 582 Peripherals & Station Integration
- 116 Amateur Radio Interests
- 809 Third-Party Software