Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, and Tuner Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
problem with SmartLink Connection with SmartSDR v2.3.9
Wolfgang Sidler
Member
I'm able to connect my Flex 6600M remotely over 4G etc. - but I'm not able to change the frequency. The Freq. will go back always to 14.260 MHz and I don't know why? If I try to change the freqeuncy with Band on the left hand side e.g. to 40m - it will show 7.xy MHz for a moment and than goes back to 20m 14.260 MHz.
I have no idea why SmartSDR v2.3.9 will behave like this.
73
Wolfgang
I have no idea why SmartSDR v2.3.9 will behave like this.
73
Wolfgang
0
Comments
-
Try reloading the Global profile. I had this same issue one time on my 6300. Rebooting the radio didn't help but reloading the profile fixed it. It was a very rare occurrence so I didn't try to track down the cause. Good Luck, Ken0
-
Is it Locked?0
-
This caused by the radio being set to low bandwidth when using SmartLink. I know how to switch to high/low bandwidth in SmartSDR iOS (for iPad), but not in SSDR for Windows. To switch back to high bandwidth, yes, load a global profile (per Tim's post, below).
https://community.flexradio.com/flexradio/topics/low-bandwidth-reset-after-local-with-smart-sdr
0
Leave a Comment
Categories
- All Categories
- 244 Community Topics
- 2.1K New Ideas
- 481 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 132 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 162 DAX
- 348 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 746 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 722 Genius Products
- 388 Power Genius XL Amplifier
- 250 Tuner Genius XL
- 84 Antenna Genius
- 225 Shack Infrastructure
- 150 Networking
- 366 Remote Operation (SmartLink)
- 120 Contesting
- 580 Peripherals & Station Integration
- 114 Amateur Radio Interests
- 805 Third-Party Software