Power genius XL on 2 meters?

  • 2
  • Question
  • Updated 2 years ago
From here:

http://www.4o3a.com/index.php/2017/03...

We are sponsoring the Bouvet Island DXpedition scheduled in early 2018. Bouvet is a 97% ice covered island in South Atlantic Ocean covering about 19 square miles.
Read more about this amazing DXpedition on their webpage: http://www.bouvetdx.org/
The DXpedition will showcase the new 4O3A Signature Power Genius 1.5 KW VHF Amplifier.
This amplifier will enable the EME team to deliver full legal limit output into a 2 meter EME antenna array.

So does this amp have 2m as an option? Or is this a special edition just for the DXpedition?
Photo of Ria - N2RJ

Ria - N2RJ, Elmer

  • 2270 Posts
  • 904 Reply Likes

Posted 2 years ago

  • 2
Photo of Sergey, R5AU

Sergey, R5AU

  • 846 Posts
  • 111 Reply Likes
Quite interesting note Ria, thank you  for update, may be special editiam with F6700?
 is anybody know about that ?
Photo of David Warnberg

David Warnberg

  • 538 Posts
  • 56 Reply Likes
Hitching a ride, I'm curious too

Thanks Ria
Photo of EA4GLI - 8P9EH - Salvador

EA4GLI - 8P9EH - Salvador

  • 1758 Posts
  • 536 Reply Likes
The expert 1.3k goes to 4m,it would be a matter of filtration to get to 2m. So it might be doable with slight modification.
Photo of Mike - W8MM

Mike - W8MM

  • 189 Posts
  • 40 Reply Likes
The devices used in the HF-6 version are specified to 500 MHz, so I'm guessing that the "Power Genius 1.5 KW VHF Amplifier" is a re-configured 2-meter-only lash up that might be able to include 222 MHz, but probably 2-meters only.  Would be pretty easy to do by only changing the RF networks to the typical VHF coax transformers and leaving out all the different lowpass filter banks required for HF use.  Here's a look at different examples for different frequencies:  http://www.nxp.com/products/rf/rf-power-transistors/rf-broadcast-and-ism/1-600-mhz-broadcast-and-ism... 
Photo of Ria - N2RJ

Ria - N2RJ, Elmer

  • 2270 Posts
  • 904 Reply Likes
I want to build a LDMOS amp that is driven direct by the 6700. It's not hard. Just one or two pallets, combiner, a small driver stage and filters, switching and protection circuits. And of course a PS.
Photo of Brian Morgan VK7RR

Brian Morgan VK7RR

  • 57 Posts
  • 11 Reply Likes
Ria, have a look st W6PQL who has kits for 1KW amps. They are very easy to assemble
Photo of Ria - N2RJ

Ria - N2RJ, Elmer

  • 2270 Posts
  • 904 Reply Likes
That's exactly where I did most of my research. :)
Photo of Marc Lalonde

Marc Lalonde

  • 356 Posts
  • 87 Reply Likes
Hi Ria  if it may help 

W6PQL  RF-DECK  and low pass filter 

i use this board whit 5db attenuator at input for drive the BLF188xr
http://www.minikits.com.au/electronic-kits/rf-amplifiers/rf-high-power/2m-8W-Amplifier

and finally a home made Arduino DUE based controller and protection board
whit Ethernet  for link to radio (soft ALC etc etc ...)  ,display is a 4D system intelligent display  

on 120V outlet i put 650W  ,1250w whit  240V

IMD was not the best but meed the regulation ,primary cause by hight gain and from  the  pre-driver board 

i have same for HF ;-)

73!  Marc L.  VE2OLM





Photo of Ria - N2RJ

Ria - N2RJ, Elmer

  • 2270 Posts
  • 904 Reply Likes
I remember seeing this. Very good. Yes this is a hobby project for me.
Photo of John - K3MA

John - K3MA

  • 280 Posts
  • 81 Reply Likes
I wonder if they will be able to produce full legal 2M output hooked direct to the Flex 6700 XTVR port with it low level RF output or if they will use a intermediate amp like the DEMI 2MLDPA.
Photo of John - K3MA

John - K3MA

  • 280 Posts
  • 81 Reply Likes
Reading the EME page for the DXpedition it appears DEMI is supplying two 2MLDPA's to the team so that answers my question.
Photo of philip.theis

philip.theis, Elmer

  • 114 Posts
  • 19 Reply Likes
That is a separate model. Ranko has been talking about this for some time.. You can also look into Larcan commercial TV amps that have been pulled from service.