Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?

SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.

Port Forwarding

Options
Tim VE6SH
Tim VE6SH Member ✭✭
edited April 2019 in FLEX-6000 Signature Series
I am having an issue configuring Smartlink on my 6600. I am running a Hitron modem from a cable provider and an IQrouter for the router and wifi. UPnP is enabled on both modem and router, but it will not automatically allow a connection. I have tried to manually port forward, but Smartlink suggests I have to forward ports “-1” which is not a value the IQ/router will let me use. Any ideas? Baffled because I have the same setup at my home location and it works fine in auto mode. 73 Tim VE6SH/7 image

Answers

  • Tim - W4TME
    Tim - W4TME Administrator, FlexRadio Employee admin
    edited March 2018
    Options
    First off, you cable modem needs to be configured for bridge mode.  If it is being used a router doing NAT and you have an IQrouter connected to it, you are doing "double NAT" and that is not going to work for SmartLink (unless you do some advanced network configuration).  You can validate a double NAT by looking at the IP address in the WAN port.  If it is not a public (routable) IP address, but a private RFC 1918 IP address (10.0.0.0/10, 172.16.0.0/12 or 192.168.0.0/16) then you are doing double NAT.

    I highly recommend using UPnP for ease of setup if possible.  Setting the cable modem in bridge mode and configuring UPnP on the IQrouter should do it.

    And the "-1" indicates that the ports configured are invalid.  The need to be numbers > 1024 and < 65535.
  • Tim VE6SH
    Tim VE6SH Member ✭✭
    edited March 2019
    Options
    Hi Tim Thanks, yes the modem is in bridge mode and I confirmed by checking the IP address in the WAN so I do not believe I am doing double NAT. UPnP is turned on in the IQrouter. What do I replace the -1? Any numbers in that range and port forward to 4993/4992? The modem ipv4 WAN address is 192.168.0.1 while the IQrouter LANis 192.168.7.100 73 Tim
  • Tim VE6SH
    Tim VE6SH Member ✭✭
    edited March 2019
    Options
    Tim


    My bad. I was told by the people who did ny wifi/cable install the modem was in bridge mode. I called the cable provider to confirm and they advised the modem was not in bridge mode. They were able to configure it remotely and now all works.


    Thank you!


    73


    Tim


    image

Leave a Comment

Rich Text Editor. To edit a paragraph's style, hit tab to get to the paragraph menu. From there you will be able to pick one style. Nothing defaults to paragraph. An inline formatting menu will show up when you select text. Hit tab to get into that menu. Some elements, such as rich link embeds, images, loading indicators, and error messages may get inserted into the editor. You may navigate to these using the arrow keys inside of the editor and delete them with the delete or backspace key.

Comment As ...

Categories