Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Pan-adapter screen shows small peaks on either side of freq when using FT8
Options
DV
Member ✭✭
When using the Maestro on FT8, when in the TX mode, I see several smaller peaks along each side of the carrier. The level meter on the DAX screen shows about 95% on TX peaks. So, as a test, I turned it down and the smaller side peaks went away so show a perfect TX peak with nice sloping sides. So, supposedly, this gives me a nice FT8 carrier without overshoot and spurs, however, I had to turn the power knob all the way up to 100 watts, to convince the Maestro to provide just 40 watts. So, to get a clean carrier, I have to reduce power. My question is, is the TX pan-adapter accurately showing spurs when the DAX level approaches 100% or is that a bug? Do I really have those spurs? (My SWR is very low... antenna is a log periodic.)
0
Answers
-
Doug,
Try turning down or turning off the receiver pre-amplifiers. The display you see on transmit is the received spectrum from leakage between the transmitter output and the receiver input. Too many preamp stages will overload producing IMD products in the transmit spectrum display and make the spectrum look worse than it actually is.
73,
Geoff-W8GNM
1
Leave a Comment
Categories
- All Categories
- 245 Community Topics
- 2.1K New Ideas
- 490 The Flea Market
- 7.4K Software
- 5.9K SmartSDR for Windows
- 135 SmartSDR for Maestro and M models
- 327 SmartSDR for Mac
- 243 SmartSDR for iOS
- 224 SmartSDR CAT
- 163 DAX
- 347 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 766 Maestro
- 42 FlexControl
- 836 FLEX Series (Legacy) Radios
- 727 Genius Products
- 392 Power Genius XL Amplifier
- 251 Tuner Genius XL
- 84 Antenna Genius
- 222 Shack Infrastructure
- 149 Networking
- 370 Remote Operation (SmartLink)
- 118 Contesting
- 582 Peripherals & Station Integration
- 116 Amateur Radio Interests
- 809 Third-Party Software