Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, and Tuner Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Odd behavior on TUNE
Ken - NM9P
Member ✭✭✭
Doing my job as a "pre-release" tester.... 6500 / flex control knob, Win-8, running current 0.13.10 software. I noticed when I had two pan windows open, one on 80 meters and the other on 10 meters, and tuned just outside the high end of 80. I hit "tune," and it didn't transmit (as expected.) But when I turned the flex knob back into the band, the rig went into "tune" mode without my hitting the button. I have repeated this several time in order to diagnose it. If I hit "tune" once, it goes into tune mode but doesn't transmit - the receiver is still operating - and if I dial back into the band the rig goes into "tune" mode. If I hit "tune" button twice, it toggles back into receive and does not go into "tune" when I dial back into the band. No biggie, but could cause a problem. Ken - NM9P
0
Comments
-
Yep, That is a bug. I have entered it into the bug tracker for further investigation. Thanks for doing a great job of being a Preview Tester!0
-
Tim, A similar thing happens if I hit "ATU" when out of band and then either move in band, or activate TX on another slice...the rig goes into MOX mode, but since the timing for antenna tune has timed out, it doesn't tune, but just stays in MOX with a hot mike. I suspect a similar logic failure to toggle OFF of the TUNE or ATU command if the frequency was out of band...0
-
This issue has been fixed in SmartSDR v0.15.x and greater1
Leave a Comment
Categories
- All Categories
- 244 Community Topics
- 2.1K New Ideas
- 481 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 132 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 162 DAX
- 348 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 746 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 722 Genius Products
- 388 Power Genius XL Amplifier
- 250 Tuner Genius XL
- 84 Antenna Genius
- 225 Shack Infrastructure
- 150 Networking
- 366 Remote Operation (SmartLink)
- 120 Contesting
- 580 Peripherals & Station Integration
- 114 Amateur Radio Interests
- 805 Third-Party Software