Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Odd result from checking .SliceList.Count
Options
Anthony Bowyer
Member ✭✭
Given that _thisRadio is a found and connected instance of Radio, I have found what seems to be an odd result from a test of the value of _thisRadio.SliceList.Count.
In this case, the radio is a 6300. If two slices are 'active', it is my assumption, that on connecting to said radio, SliceList.Count will be 2. Single stepping thru a simple program shows this to be the case until it gets to a line that says "If (_thisRadio.SliceList.Count > 1)", etc.
At this point, SliceList,Count becomes 0. If I set a variable to SliceList.Count, and test the variable there's no issue, but if I test directly, it will get changed to 0 every time.
I assume something is changing it, but there's nothing in place in the program that does so and I am unable to find anything in Flexlib that might be doing it (though searching thru it is a bit tedious when you aren't sure what you're looking for).
In this case, the radio is a 6300. If two slices are 'active', it is my assumption, that on connecting to said radio, SliceList.Count will be 2. Single stepping thru a simple program shows this to be the case until it gets to a line that says "If (_thisRadio.SliceList.Count > 1)", etc.
At this point, SliceList,Count becomes 0. If I set a variable to SliceList.Count, and test the variable there's no issue, but if I test directly, it will get changed to 0 every time.
I assume something is changing it, but there's nothing in place in the program that does so and I am unable to find anything in Flexlib that might be doing it (though searching thru it is a bit tedious when you aren't sure what you're looking for).
0
Answers
-
I believe that the slice count starts at 0. Slice A=0 Slice B=1, etc. So, if you are getting 1 back, then that "should" mean you have two active slices. I'm sure I read that somewhere here in a post by Steve. James WD5GWY0
-
I'm too quick on the trigger! My response wasn't what you were looking for. Sorry about that.0
Leave a Comment
Categories
- All Categories
- 246 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 163 DAX
- 348 SmartSDR API
- 8.6K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 766 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 733 Genius Products
- 393 Power Genius XL Amplifier
- 255 Tuner Genius XL
- 85 Antenna Genius
- 229 Shack Infrastructure
- 153 Networking
- 370 Remote Operation (SmartLink)
- 120 Contesting
- 583 Peripherals & Station Integration
- 115 Amateur Radio Interests
- 813 Third-Party Software