Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Is there a way to lock transverter ports to a particular transverter defination?
Options
Tom Worthington
Member ✭✭
I have two transverters connected to my 6600M, one for 2m and one for 70cm. Unless I were to change to connections on the back, the 2m transverter will always want to use XVTRA connections and the 70cm will use XVTRB. Much of the time the radio seems to remember this and connect appropriately when I open a slice on either 2m or 70cm, but not always. Especially when I am trying to do satellite communication I'll look over and see that it has changed either the receive or transmit connections to the incorrect ports.
(Thanks for having the 4th transmit keying line in the ACC connector. I have 2 HF amplifiers and the two transverters so I use all 4 of those connections)
(Thanks for having the 4th transmit keying line in the ACC connector. I have 2 HF amplifiers and the two transverters so I use all 4 of those connections)
1
Answers
-
did you ever get an answer to this?0
-
I made a NodeRed flow that follows the frequency of each slice, and depending on the BAND of each slice, sets the antenna ports to whatever is appropriate for that band. I have a single IF Q5 transverter for UHF, so that one is set to XVTB for both TX and RX, but on VHF I have a split IF DEMI transverter, so when the band is UHF, it selects XVTA for TX and RX_A for RX. When an HF frequency is selected in a slice, it selects ANT1 for both TX and RX.
Charlie KB8CR
0
Leave a Comment
Categories
- All Categories
- 245 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.3K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 327 SmartSDR for Mac
- 241 SmartSDR for iOS
- 224 SmartSDR CAT
- 161 DAX
- 343 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 768 Maestro
- 42 FlexControl
- 836 FLEX Series (Legacy) Radios
- 726 Genius Products
- 391 Power Genius XL Amplifier
- 251 Tuner Genius XL
- 84 Antenna Genius
- 221 Shack Infrastructure
- 149 Networking
- 369 Remote Operation (SmartLink)
- 118 Contesting
- 582 Peripherals & Station Integration
- 116 Amateur Radio Interests
- 809 Third-Party Software