Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Is it possible to ssh or telnet into the O.S. running in my 6300?
Options
Gary L. Robinson
Member ✭✭
I ask this question because I installed a waveform into my 6300 and misspelled the end of the waveform name as wavefor -- leaving the m off the end. Every time I uninstall it, it disappears from the waveform list but after shutting down my 6300 and later turning it on I see it again in the waveform list in the WaveForm Manager. I suspect it is not really uninstalling it because of the letter m I left off of the waveform name hihi
It's not a major deal but is a bit annoying. If I could ssh into the underlying O.S. (which I suspect is not something I can do) then I might be able to manually delete the waveform file.
Alternately, I could do a factory reset and that might take care of the problem but being lazy I would rather not do that especially when it is just a slight nuisance.
---Gary WB8ROL
It's not a major deal but is a bit annoying. If I could ssh into the underlying O.S. (which I suspect is not something I can do) then I might be able to manually delete the waveform file.
Alternately, I could do a factory reset and that might take care of the problem but being lazy I would rather not do that especially when it is just a slight nuisance.
---Gary WB8ROL
0
Answers
-
Nope.. not something you can do.0
-
Thanks Chris, I figured it was worth asking though hihi.0
-
You do get extensive access via the API though.0
-
The question needs a little more detailed answer, IMHO.
s Chris indicated you cannot establish a session with the operating system running on the radio.
You can, however, telnet to port 4992 and communicate with the SmartSDR "command channel" by issuing API based commands to subscribe to radio events and manipulate radio resources (create panadapters and slices, tune slices, enable/disable radio features, etc..) and Ria indicated.
And to address your original question, you need to do a factory reset to properly remove waveforms that are not manageable by the usual means.0
Leave a Comment
Categories
- All Categories
- 246 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 163 DAX
- 348 SmartSDR API
- 8.6K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 766 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 733 Genius Products
- 393 Power Genius XL Amplifier
- 255 Tuner Genius XL
- 85 Antenna Genius
- 229 Shack Infrastructure
- 153 Networking
- 370 Remote Operation (SmartLink)
- 120 Contesting
- 583 Peripherals & Station Integration
- 115 Amateur Radio Interests
- 813 Third-Party Software