Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Interfacing a 3rd-party panadapter program with Flex 6000 series radio
Options
Dan Trainor
Member ✭✭✭
I have a separate RX station that uses an SDRPlay RSP2 with a W6LVP mag loop rx antenna and I would like to interface the PC panadapter software SDRuno using SmartSDR-CAT. (T/R switching and rx muting is already worked out) The integration is just for synching the band, freq, and mode. I find the waveform and waterfall processing in SDRUno to be highly advanced and desirable, so I would like to display the Flex SmartSDR panadapter on one display and SDRUno on another. To sync SDRUno with any radio, it happens to use OMNIRIG to pass the CAT commands to / from the radio. For Flex radio, I assume I will be creating a CAT port of protocol "CAT" and port type "Serial" and either "FlexVSP" or "Existing"? (not sure which yet). And VFO Slice set to "A". And Auto TX Slice set to "Enabled". Question: Am I on the right track here? I am very new as I just purchased a 6400 a few days ago. But I am already deep into the manuals. Thanks in advance! Dan WA1QZX
2
Leave a Comment
Categories
- All Categories
- 246 Community Topics
- 2.1K New Ideas
- 489 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 223 SmartSDR CAT
- 163 DAX
- 348 SmartSDR API
- 8.6K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 766 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 733 Genius Products
- 393 Power Genius XL Amplifier
- 255 Tuner Genius XL
- 85 Antenna Genius
- 229 Shack Infrastructure
- 153 Networking
- 370 Remote Operation (SmartLink)
- 120 Contesting
- 583 Peripherals & Station Integration
- 115 Amateur Radio Interests
- 813 Third-Party Software