Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Flex-5000, PowerSDR, and WSJT-X
Options
K1SZO
Member ✭✭
Hello all,
I have a friend that has a Flex-5000, uses PowerSDR, and wants to setup WSJT-X with it. I've read the howto knowledge base article on setting these up, but the instructions seem quite dated and do not seem to jive anymore.
We were using com-0-com and VAC, but PowerSDR did not like it when I set the driver to Windows WDM-KS and the Virtual Cable 1 and 2.
Also, I can't for the life of me figure out how to get CAT control working either.
Does someone know of some updated instructions to get this configuration up and running?
73, David ~ K1SZO
I have a friend that has a Flex-5000, uses PowerSDR, and wants to setup WSJT-X with it. I've read the howto knowledge base article on setting these up, but the instructions seem quite dated and do not seem to jive anymore.
We were using com-0-com and VAC, but PowerSDR did not like it when I set the driver to Windows WDM-KS and the Virtual Cable 1 and 2.
Also, I can't for the life of me figure out how to get CAT control working either.
Does someone know of some updated instructions to get this configuration up and running?
73, David ~ K1SZO
0
Answers
-
RE setting up the CAT - you might make note of this one particular setting that drove me nuts till I finally figured it out. See this link to my previous post https://community.flexradio.com/flexradio/topics/wsjt-x-with-powersdr-and-dxlab
0 -
I have the same hardware setup, also using com-0-com and VAC. As driver for VAC I use MME. Though for CAT I use DXLab Commander.
No problems at all.
73, Peter - HB9BUN0 -
I use com0com, vac line 1 for in/out and omnirig Working fine for me
73 oz1hdf0
Leave a Comment
Categories
- All Categories
- 245 Community Topics
- 2.1K New Ideas
- 490 The Flea Market
- 7.4K Software
- 5.9K SmartSDR for Windows
- 135 SmartSDR for Maestro and M models
- 327 SmartSDR for Mac
- 243 SmartSDR for iOS
- 224 SmartSDR CAT
- 163 DAX
- 347 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 768 Maestro
- 42 FlexControl
- 836 FLEX Series (Legacy) Radios
- 727 Genius Products
- 392 Power Genius XL Amplifier
- 251 Tuner Genius XL
- 84 Antenna Genius
- 222 Shack Infrastructure
- 149 Networking
- 370 Remote Operation (SmartLink)
- 118 Contesting
- 582 Peripherals & Station Integration
- 116 Amateur Radio Interests
- 811 Third-Party Software