Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Fldigi Does Not Switch Back to rx From tx
Options
Alan
Member ✭✭✭✭
Flex 6600, Paralles / Windows 11, FLDIGI version 4,1,02, SliceMaster 0.10.6b.
Using macros to control FLDIGI. After tx, macro does not cause Flex 6600 to return to rx (receive). Checked curser follows the "tith r" character. Removed FLDIGI, rebooted windows and same problem.
FLDIGI setup using SliceMaster 6000. Slicemaster reports no problems.
Problem / need help getting FLDIGI to return FLEX to receive after transmission is complete.
Thanks.
Using macros to control FLDIGI. After tx, macro does not cause Flex 6600 to return to rx (receive). Checked curser follows the "tith r" character. Removed FLDIGI, rebooted windows and same problem.
FLDIGI setup using SliceMaster 6000. Slicemaster reports no problems.
Problem / need help getting FLDIGI to return FLEX to receive after transmission is complete.
Thanks.
0
Comments
-
One more data point. After more trial and error, in every case when I start flDigi from Slicemaster, everyting appears to work well. Only when I use a macro to tx, the flDigi programs freezes. The message continues to be sent and when the macro reaches the end with the command to return to rx, because it is locked up, the Flex 6600 transmitter does not return to rx.
Following the failure to return to rx, with the program locked up, I must do a forced shutdown and restart to return the program to operating status.0 -
I do not use SliceMaster for FlDigi, but direct with Mac and Windows I have absolutely no problems with FlDigi macros and Tx/Rx toggle. Have you tried just starting up FlDigi with its standard macros? Have never had an issue with it. Flex6600M in use here, with CAT/DAX on Windows and xCat/xDax on Mac.0
-
Configured FlDigi manualy using the Rig Cat selection on the configure menu. All functions appear to work OK with no program freeze ups and it returns to rx after a transmission.
Flexmaster used the flrig and hamlib selections under rig configuration. This again cause FlDigi to lockup when the transmission was done.
Appears to narrow the problem down to the configuration setup from Flexmaster. Could there be a missing piece of software??
0 -
I’m using Hamlib with xCat and TCP/IPRigCtl on the Mac, and RigCAT with COM4 on Windows, and all of them work just fine with FlDigi.0
-
Configured FlDigi manualy using the Rig Cat selection on the configure menu. All functions appear to work OK with no program freeze ups and it returns to rx after a transmission.
Flexmaster used the hamlib selections under rig configuration. This again cause FlDigi to lockup when the transmission was done.
Appears to narrow the problem down to the configuration setup from Flexmaster. Could there be a missing piece of software??
0
Leave a Comment
Categories
- All Categories
- 246 Community Topics
- 2.1K New Ideas
- 489 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 163 DAX
- 348 SmartSDR API
- 8.6K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 766 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 733 Genius Products
- 393 Power Genius XL Amplifier
- 255 Tuner Genius XL
- 85 Antenna Genius
- 229 Shack Infrastructure
- 153 Networking
- 370 Remote Operation (SmartLink)
- 120 Contesting
- 583 Peripherals & Station Integration
- 115 Amateur Radio Interests
- 813 Third-Party Software