Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
External receiver connect for Flex 6700
Options
Slawomir
Member ✭✭
Hi All,
How can you connect an external receiver to the antenna to work in parallel with the FLEX-6700? The rear panel has BNC Ant IN and Ant OUT sockets. How do you configure them in Smart SDR?
How can you connect an external receiver to the antenna to work in parallel with the FLEX-6700? The rear panel has BNC Ant IN and Ant OUT sockets. How do you configure them in Smart SDR?
0
Comments
-
Try this: Using two short BNC jumpers and a female "T" BNC connector; jumper a loop in to BNC "T" and loop out to other end of the BNC "T" then connect the second radio to the remaining female BNC "T" connection. In the ANT panel turn on the LOOP you connected to. You will have to determine if there are any negative effects on the Flex radio when activating the LOOP circuit to the second radio. Let us know how it works.
0 -
Using a splitter is the right solution. Using a T-connector is not RF like0
-
I would do neither. RF could jump the splitter network and damage your radio. The T connector is a definite no-no. There are a few T/R boxes out there that will take care what you want to do.0
-
a splitter in RX pass of a TRX can what? Sorry, if it's true then all SDR stick user do it wrong, and also all preselector user.
Many Ham's worldwide use this technics and use Pan adapter via a SDR stick and SDR soft - and it works great.
Cant see the problem0 -
What happens when you transmit. You have RF going straight into the receiver or SDR stick. As a matter of fact the SDR stick guys tell you to ground the antenna input to the SDR stick when transmitting.
Good Luck0 -
Hi,
I bought Play SDR and I want to use it together with Flex 6700. On the BNC sockets the rx antenna on the back of the panel has no signal to the external receiver. It remains enabled for Play SDR a piece of wire as an antenna because I do not know if the use of the splitter after turning on the Flex6700 TC does not will damage Sdr Play. In Yaesu, the FT 3000 is on such a RX uot signal and a colleague works without a problem with the connected SDR Play.
Slawomir
0
Leave a Comment
Categories
- All Categories
- 246 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 163 DAX
- 348 SmartSDR API
- 8.6K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 765 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 733 Genius Products
- 393 Power Genius XL Amplifier
- 255 Tuner Genius XL
- 85 Antenna Genius
- 228 Shack Infrastructure
- 152 Networking
- 370 Remote Operation (SmartLink)
- 120 Contesting
- 583 Peripherals & Station Integration
- 115 Amateur Radio Interests
- 811 Third-Party Software