Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Don't see RF Power / SWR levels in SDR when transmitting phone
Options
K1TZT
Member
I'm using the Flexradio 6300 for phone operation for the first time .. I had previously used it just for digital modes and is working fine. I have a USB headset for phone on my PC with SDR. The issue I see is when I press "MOX" I don't see any RF Power level or SWR level outputs. I do see my carrier signal in the signal display graph and the TX ready goes RED. The RF Power / SWR does show levels though when I press "TUNE" Is it normal not to see any levels when TXing with MOX?
0
Answers
-
If you don't turn dax off it will not pass microphone audio when using mox to key the radio.1
-
Select Pc in the input drop down just above Proc button
0 -
Thanks for the quick replies.. I made sure I have both dax off and PC selected.. however I still don't see RF Power SWR level when pressing MOX only TUNE. I attached screen "MOX" and "TUNE" in case you see something else I'm missing. John K1TZT0
-
In your computer, make sure default recording device is selected,,in audio devices and is showing response to you voice.
0 -
I don't generally press the MOX button, but my 6500 does the same thing..............until I speak into the mic.
If you're speaking after pressing MOX and not showing any power out, I don't know what is going on.
Tom N5MOA
1 -
If can't get audio from your computer,,do you have a mic to plug into the Flex?
1 -
On SSB modes there is no output if audio is not present.1
-
Thanks for the replies.. I checked the USB Mic more based on your feedback.. I found the gain wasn't high enough. Once I increased I now see RF power level / SWR when speaking.. I was expecting the RF power level meter = to the RF power level setting (100 Watts in this case) when keying the mic.. but it bounces a lot based on Mic level which looks expected then.. Thx
John K1TZT0 -
Ok glad it works, set the gain in the computer fairly high, then adjust the mic gain in SSDR were it should be.
0
Leave a Comment
Categories
- All Categories
- 246 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 163 DAX
- 348 SmartSDR API
- 8.6K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 766 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 733 Genius Products
- 393 Power Genius XL Amplifier
- 255 Tuner Genius XL
- 85 Antenna Genius
- 229 Shack Infrastructure
- 153 Networking
- 370 Remote Operation (SmartLink)
- 120 Contesting
- 583 Peripherals & Station Integration
- 115 Amateur Radio Interests
- 813 Third-Party Software