Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, and Tuner Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Disconnect recovery
N7BCP
Member ✭✭
For the most part, remote over wireless N has been working well. Occasionally, I'll have a radio disconnect during a QSO. Last night while in a JT65 contact I had a disconnect and once the radio was disconnected the JT65 serial link to the flex crashed. Upon restarting SSDR the radio shows red busy in the radio chooser. Until that disconnect the remote quality bars were full green. Maybe a spike in latency? Power off and on the radio and then I'm able to start SSDR but QSO is done by this time. I remember when PowerSDR would not recover from FireWire issues automatically and then finally with a new release the radio was able to recover on its own. I'd like to see some sort of retry logic hat would allow the radio and SSDR to re establish a connection automatically. Having the RX freeze momentarily would be better than a complete disconnect. Running 6500, SSDR 1.4.3 Mac book pro with 8gb ram windows 8.1 boot camp (not using virtualization). I'm about 15 meters from the access point. I don't doubt I will have the occasional long DPC or network blip, would just like to see a better user experience without the radio, SSDR, and CAT restart needed, especially during a contact. 73 Larry HB9EYQ
0
Comments
-
I have entered this report into our bug tracker for further investigation. Please report any additional information related to this specific issue in this community topic.
0
Leave a Comment
Categories
- All Categories
- 244 Community Topics
- 2.1K New Ideas
- 481 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 132 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 162 DAX
- 348 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 745 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 722 Genius Products
- 388 Power Genius XL Amplifier
- 250 Tuner Genius XL
- 84 Antenna Genius
- 225 Shack Infrastructure
- 150 Networking
- 366 Remote Operation (SmartLink)
- 120 Contesting
- 580 Peripherals & Station Integration
- 114 Amateur Radio Interests
- 805 Third-Party Software