Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
DAX Audio RX 1 Problem
Options
iz7auh
Member ✭✭
Hi when I choose DAX 1 channel on SLICE A a audio signal go to DAX RX 1 I/Q why? ch 2/3/4.../7 no problem
0
Comments
-
I have a similar problem. FLEX 6300, WIN 7, N1MM with MMTTY and 2-Tone. When I bring up soundcard setup in MMTTY, DAX RX Audio 1 and 2 are not there (3-8 are, but I cannot use them with the 6300). TX audio 1 and 2 are there and work fine. However, when I bring up 2-Tone audio soundcard setup, DAX 1 and 2 are there and work fine. How can I get RX Audio 1 and 2 to show with MMTTY?0
-
Mike...
Go into Windows sound manager "recording" tab. Right click and select "show disabled devices" as I suspect that DAX audio RX1 and RX2 may have inadvertently been disabled. If so, simply right click each device and select "enable". 73 and hope this helps,
Don
K4QKY0 -
Mike, the enable / disable feature in the soundmanager was a good hint for my easypal problem. Easypal cannot handle all the audio devices smartSDR creates. So only a few of them can be selected by the programm. But the programm checks for the enabled devices only. So after disabling unneeded devices I found a pair for TX and RX. Not a universal solution, but may help sometimes.
0 -
Don: That wasn't it, but nosing around I found the problem. Looks as if MMTTY can only display 16 sound devices, while 2-tone displays more. DAX RX Audio 1 and 2 are devices 17 and 20. I expect if I delete devices 7 and 8 (which are in the first 16) I'll see my DAX connections. --Mike0
-
I had the same problem with MultiPSK. It will only show 16 devices and was showing everything but the two I needed. I deleted DAX channels 3-8 (both TX and RX) since I can't use them with the 6300. Problem solved.
0 -
With a 6300, you can deactivate regular DAX channels 3-8 on ex, Tx, and reserved, because they will not be used. It clears a lot up. Also, remember to go to audio properties for all of your inputs and outputs on both ends of the "cable" and set the properties to 16 bit stereo 48000 bit sampling. It will eliminate math conversion errors between DAX and your digi software.1
Leave a Comment
Categories
- All Categories
- 245 Community Topics
- 2.1K New Ideas
- 490 The Flea Market
- 7.4K Software
- 5.9K SmartSDR for Windows
- 135 SmartSDR for Maestro and M models
- 327 SmartSDR for Mac
- 243 SmartSDR for iOS
- 224 SmartSDR CAT
- 163 DAX
- 347 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 767 Maestro
- 42 FlexControl
- 836 FLEX Series (Legacy) Radios
- 727 Genius Products
- 392 Power Genius XL Amplifier
- 251 Tuner Genius XL
- 84 Antenna Genius
- 222 Shack Infrastructure
- 149 Networking
- 370 Remote Operation (SmartLink)
- 118 Contesting
- 582 Peripherals & Station Integration
- 116 Amateur Radio Interests
- 811 Third-Party Software