Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
CW Latency on 6500 with current software
Options
K8AC
Member ✭✭
Recently acquired a 6500 and was curious about the latency involved in receive and transmit with the current software, and factors that might influence it. I ran some tests comparing my 6500 to an Elecraft transceiver that might be of interest to CW DXers and contesters. To get the paper with scope photos, etc., use the link below to download the PDF file. Questions and comments welcome here.
www.k8ac.net/Latency.html
www.k8ac.net/Latency.html
0
Answers
-
Good information. I am a CW only op as well. I read about the same here. I ran an additional test here with my 6500 on the timing delay between the TX1 and when the RF envelope starts and stops. They did a great job on the new software. I measure 2ms between TX1 going active or low and the RF envelope starting and the same 2ms between when the RF envelope stops and then the TX1 line goes inactive or high. Perfect for a PIN diode amp such as my KPA1500. You can run with zero TX delay on the settings. With my SPE Expert and my Icom PW1 I run 10 ms. delay on the setup. Both of these amps switch around 6ms (they use relays).
I just upgrade to a 6600 and will check but my guess is the timings will be the same.
Tom
K3TF...
0
Leave a Comment
Categories
- All Categories
- 245 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.3K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 327 SmartSDR for Mac
- 241 SmartSDR for iOS
- 224 SmartSDR CAT
- 161 DAX
- 343 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 768 Maestro
- 42 FlexControl
- 836 FLEX Series (Legacy) Radios
- 726 Genius Products
- 391 Power Genius XL Amplifier
- 251 Tuner Genius XL
- 84 Antenna Genius
- 221 Shack Infrastructure
- 149 Networking
- 369 Remote Operation (SmartLink)
- 118 Contesting
- 582 Peripherals & Station Integration
- 116 Amateur Radio Interests
- 809 Third-Party Software