Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
CW and Amplifier problem
Options
Enrique Rabczuk
Member ✭✭
My setup is Flex 6400 and IC PW1 amplifier:
My Flex is already configurnng the Profile for SSB,RTTY,WSJT-Xthese modes work very well. It was impossible to configure the CW mode. I can transmit once and the second time the amplifier goes into protection, this only happens with CW mode in any band.To check out the problems with the amplifier, configure as you did before purchasing the Flex setup was (IC 7600 and IC PW1 )and it work very well in all modes. Does anyone have an idea why only the CW disables the amplifier? The test was do with same antennas.Thanks for the help.
My Flex is already configurnng the Profile for SSB,RTTY,WSJT-Xthese modes work very well. It was impossible to configure the CW mode. I can transmit once and the second time the amplifier goes into protection, this only happens with CW mode in any band.To check out the problems with the amplifier, configure as you did before purchasing the Flex setup was (IC 7600 and IC PW1 )and it work very well in all modes. Does anyone have an idea why only the CW disables the amplifier? The test was do with same antennas.Thanks for the help.
0
Answers
-
Try setting your tx delay for 20 or 30 ms0
-
Hi Al.
I made the suggested changes, but it´s still the same.
0 -
my first guess is high swr... being detected in cw mode by the amp
see pw1 manual
or
You may need to cut back on power out from the flex...
I would start out with 30 watts and slowly work up to 100 watts in 10 watt increments
and see where the protection circuits kicks in.
Paul K3SF
0 -
Hi Paul,
I try with different setting 5, 10, 30, 50 watts stiil same.
Also I try with a dummy load and still same. This problem is only in CW mode. Other modes are very well example RTTY 500 watts or 1Kw, no problem, SSB 500 watts or more no problem.Thank.
73
Enrique, CP6UA
0 -
When you do a new radio need to reset the ACL, as it will work without doing that , but maybe casueing something if not reset. I use a CT-17 level and the DTTUI- v3 software(this is use just for the PW-1), is working good.
0
Leave a Comment
Categories
- All Categories
- 246 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 163 DAX
- 348 SmartSDR API
- 8.6K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 765 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 733 Genius Products
- 393 Power Genius XL Amplifier
- 255 Tuner Genius XL
- 85 Antenna Genius
- 229 Shack Infrastructure
- 153 Networking
- 370 Remote Operation (SmartLink)
- 120 Contesting
- 583 Peripherals & Station Integration
- 115 Amateur Radio Interests
- 812 Third-Party Software