Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
click tune direction
Options
W4YXU
Member
A minor confusion/annoyance: While searching for an expected QSO somewhere in a stretch of band about 50 or 100 khz I notice that when using click tune and 1khz steps set to snap to the step it goes to the next one LOWER instead of the expected nearest step. This makes it a bit harder to hit the desired spot instead of being on the wrong khz most of the time. I am embarrassed that it took me this long to realize that I wasn't quite as in-accurate in mouse positioning!
0
Comments
-
This looks to be a defect. I am looking into it.
0 -
The 1.2.1 release is SUPER!
OK and thanks. The stated problem appears to be ALMOST fixed (or maybe we got a new feature?!).
It does snap to the appropriately rounded stem UNLESS you click in the blue filter area on the screen in which case there is no snap to step.
Problem or feature?
0 -
This is actually a feature and not a defect. The presumption is that if you are click tuning inside of the active slice RX passband you are wanting to tune to that exact frequency. This is necessary for narrow band modes.1
-
Well, I consider it a defective feature! When poking around an SSB jungle I occasionally miss and need to go down in freq (On 40m!) 1khz but the exact click tune is essentially impossible to place on any specific desired frequency. I can see somewhat less than no use for this feature. I welcome and encourage enlightenment! Microsoft also makes a lot of questionable assumptions about what the user wants =(-
0
Leave a Comment
Categories
- All Categories
- 246 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 163 DAX
- 348 SmartSDR API
- 8.6K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 766 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 733 Genius Products
- 393 Power Genius XL Amplifier
- 255 Tuner Genius XL
- 85 Antenna Genius
- 229 Shack Infrastructure
- 153 Networking
- 370 Remote Operation (SmartLink)
- 120 Contesting
- 583 Peripherals & Station Integration
- 115 Amateur Radio Interests
- 813 Third-Party Software