Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
6700 RX signal noise problem between ant 1 and 2
Options
Nigel
Member ✭✭
noise levels are stronger than the signals when switching RX and TX antenna selections with or without an antenna connected to either antenna port. by switching the TX antenna to an unconnected port I get low back ground noise and can RX
-60db
-117 db
I think there may be a fault but have no way of diagnosing this.
the radio info is:-
Serial: 3714-4168-6700-1264,
ID: 00-1C-2D-02-03-32,
RadioIP: 192.168.1.239,
Firmware: v2.3.9.112
ssdr version V2.3.9
I did try a roll back to V2.0.19 but made no difference.
any help would be very much appreciated.
-60db
-117 db
I think there may be a fault but have no way of diagnosing this.
the radio info is:-
Serial: 3714-4168-6700-1264,
ID: 00-1C-2D-02-03-32,
RadioIP: 192.168.1.239,
Firmware: v2.3.9.112
ssdr version V2.3.9
I did try a roll back to V2.0.19 but made no difference.
any help would be very much appreciated.
0
Comments
-
Hi Nigel - I cannot duplicate the problem here with a 6600M (same HW Version) and two separate antennas attached to ANT1 and ANT2. The noise floor changes slightly without the antennas being connected, and the antennas are slightly different, but nothing unusual. What you're seeing looks extraordinary to me.
I know it's probably overkill, but I keep a receiver guard on ANT2 because I only use it only for Rx. Good luck !
73
Jim, WQ2H
1 -
Well i guess its time to raise a ticket for repair.
0
Leave a Comment
Categories
- All Categories
- 245 Community Topics
- 2.1K New Ideas
- 490 The Flea Market
- 7.4K Software
- 5.9K SmartSDR for Windows
- 135 SmartSDR for Maestro and M models
- 327 SmartSDR for Mac
- 243 SmartSDR for iOS
- 224 SmartSDR CAT
- 163 DAX
- 347 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 768 Maestro
- 42 FlexControl
- 836 FLEX Series (Legacy) Radios
- 727 Genius Products
- 392 Power Genius XL Amplifier
- 251 Tuner Genius XL
- 84 Antenna Genius
- 222 Shack Infrastructure
- 149 Networking
- 370 Remote Operation (SmartLink)
- 118 Contesting
- 582 Peripherals & Station Integration
- 116 Amateur Radio Interests
- 811 Third-Party Software