6700 on data modes

  • 1
  • Question
  • Updated 3 years ago
6700 on PSK31 JT9 etc
Photo of Jon D Hague

Jon D Hague

  • 6 Posts
  • 1 Reply Like

Posted 3 years ago

  • 1
Photo of Jim Gilliam

Jim Gilliam

  • 883 Posts
  • 195 Reply Likes
Flgigi and WSJT-X
Photo of Ray Andrews, K9DUR

Ray Andrews, K9DUR, Elmer

  • 244 Posts
  • 61 Reply Likes
What is your question? -- 73, Ray, K9DUR
Photo of George Molnar, KF2T

George Molnar, KF2T, Elmer

  • 1612 Posts
  • 570 Reply Likes
Works great. Have made thousands of digital contacts 160-2M. Question?
Photo of Jon D Hague

Jon D Hague

  • 6 Posts
  • 1 Reply Like
I would if I could likewise
Trying to set up data modes on 6700 namely JT65 JT9 PSK31need a step by step installation guide ..check list
Looked at facebook ideos but the displayed screens contain too many bits of data and assume too much .
Not able to interconnect output of 6700 to say JT65 program or get the program to send via output of JT65 to activate 6700
Increasingly frustrated by plethora of Com ports; DAX, CAT; Slices  etc
Please untangle me
Photo of Jon D Hague

Jon D Hague

  • 6 Posts
  • 1 Reply Like
Trying to set up data modes on 6700 namely JT65 JT9 PSK31need a step by step installation guide ..check list
Looked at facebook ideos but the displayed screens contain too many bits of data and assume too much .
Not able to interconnect output of 6700 to say JT65 program or get the program to send via output of JT65 to activate 6700
Increasingly frustrated by plethora of Com ports; DAX, CAT; Slices  etc
Please untangle me
Photo of George Molnar, KF2T

George Molnar, KF2T, Elmer

  • 1612 Posts
  • 570 Reply Likes
Transmit settings:

You're almost there! Most of the receive settings have you in a very good place for transmitting. This will be an easy part.

In the DAX control panel, check the TX Stream (topmost) setting. Press the TX button if it is gray. It should turn yellow. Set the slider about halfway. 

In your digital software, set the transmit source to DAX TX. There is only one DAX TX - whatever slice is selected for transmit will look to this channel. Again, no using the "reserved" channels. 

Back in Smart SDR, look at the P/CW tab on the right side of the screen. You may need to select it from the top if it's not showing, or scroll down to it. It's the one with the "Level" and "Compression" meters. In the lower right, it has a button marked DAX. Click it to turn it blue. DAX audio will now be connected to your transmitter.

In DAX Control Panel, the TX stream should also report "streaming" and have turned blue.

In your digital mode software, generate a TUNE signal. Most applications have provision to generate a pure tone. You should see the TX Stream meter on the DAX control panel deflect. At this point, you're likely not transmitting. That's okay.


Next step: ON THE AIR!
Photo of George Molnar, KF2T

George Molnar, KF2T, Elmer

  • 1612 Posts
  • 570 Reply Likes
Transmitting!

There are a couple ways of turning on your transmitter while operating digital.

The simplest is probably just by using VOX. It's in the PHNE tab. You may need to tweak the sensitivity a bit, and keep the delay above the point where your relays chatter.

That'll get you going!


Smart CAT is an amazing tool that allows you to control your rig and send PTT commands without having to worry about VOX settings. Once you're comfortable with the way the rig works, come back to it and set it up. 

In short, Smart CAT sets up your first COM port automatically. You don't need to do anything else. It's usually COM4. In your digital program, set CAT control to use KENWOOD TS2000 protocol on COM4. Use all default settings.  Allow "PTT via CAT" if presented with that option.

The "gotcha" here is that if you use more than one CAT-enabled program AT THE SAME TIME, you need to create additional COM ports and assign unique ones to each application. It's a good thing to do anyway even if you don't use simultaneous apps, but not strictly necessary.
Photo of Jon D Hague

Jon D Hague

  • 6 Posts
  • 1 Reply Like
My problem is that I cannot get past DAX control panel  v.7.30.160 which reports driver error.. may be caused by logitec keyboard and radio mouse grabbing com ports
Photo of George Molnar, KF2T

George Molnar, KF2T, Elmer

  • 1612 Posts
  • 570 Reply Likes
COM ports and DAX have nothing to do with each other. Search the Community for W4TME's excellent guide to doing a complete removal and re installation of your Flex software. Start fresh. Follow Tim's instructions to the letter - don't skip any steps or take them out of order.
Photo of Ernest - W4EG

Ernest - W4EG

  • 607 Posts
  • 117 Reply Likes

Excellent and simple explanation George...

However, I noticed that he has the same error that I had with CAT and Dudley resolved that issue.

Hopefully, he'll follow through and submits a help desk request.

Photo of James Kennedy-WU5E

James Kennedy-WU5E

  • 314 Posts
  • 32 Reply Likes
this covers JT65/9 Ok download WSJT-X , once downloaded and installed open WSJT-X and open settings F2 under the Audio tab select your setting for DAX stuff, This assuming you have set all the CAT settings.

Jim
WU5E
 
Photo of James Kennedy-WU5E

James Kennedy-WU5E

  • 314 Posts
  • 32 Reply Likes
I also use JTAlert-X which is so slick and logs everything into my A/C LOG
Jim
WU5E
Photo of James Kennedy-WU5E

James Kennedy-WU5E

  • 314 Posts
  • 32 Reply Likes
Photo of Jon D Hague

Jon D Hague

  • 6 Posts
  • 1 Reply Like
very useful but stuck on DAX control panel Error
Photo of Tim - W4TME

Tim - W4TME, Customer Experience Manager

  • 9153 Posts
  • 3496 Reply Likes
If you have DAX errors, I recommend submitting a support ticket via our HelpDesk (http://helpdesk.flexradio.com) so we can assign you a case number.  For details on how to submit a HelpDesk support ticket, please refer to the following URL: http://helpdesk.flexradio.com/hc/en-us/articles/202118688-How-to-Submit-a-Request-for-Technical-Supp...   Once the support ticket is submitted, a support engineer will be in contact so we can work on the issue.