Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, and Tuner Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
6400M ATU Installation
Rod KI7CQ
Member
Just received the ATU for my 6400M. I took the top cover off but can't figure out where it goes.
Are there installation instructions for this ATU? There aren't any in the Downloads section.
Thanks.
Rod
Are there installation instructions for this ATU? There aren't any in the Downloads section.
Thanks.
Rod
0
Answers
-
I have taken my flex-6400 apart and have some pictures for you.
1: Used #8 Torx to remove all screws for bottom, including the feet.
2: On the right, looking from the front, there is a metal plate
just above the PA.
3 : Remove the 4 screws, one is the back.
4:The 2 open male connectors near the back of the PA , plug the
longest coax with the straight connector to the left side and
short one to the right side connector. Feed through the hole
first, do not grab the coax or pull on it. it takes little pressure
to insert the connector.
metal chassis.
5: Plug the ribbon cable into the Pa board first, on the right side of the picture.
6: **** down the ATU metal frame to the unit and then
attach the ATU with 4 screws.
7 Plug the coax and ribbon cables.
I hope this helps and my direction are not confusing, good luck.
Mike, VA3MD
0 -
Thank you very much for the help, Mike. I will do this tonight.
73
Rod
0 -
For everyone else who needs to do this, Mike's directions worked great.
Thanks again.
Rod
0 -
I cant believe it didnt come with detailed instructions0
Leave a Comment
Categories
- All Categories
- 244 Community Topics
- 2.1K New Ideas
- 481 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 132 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 162 DAX
- 348 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 746 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 722 Genius Products
- 388 Power Genius XL Amplifier
- 250 Tuner Genius XL
- 84 Antenna Genius
- 225 Shack Infrastructure
- 150 Networking
- 366 Remote Operation (SmartLink)
- 120 Contesting
- 580 Peripherals & Station Integration
- 114 Amateur Radio Interests
- 805 Third-Party Software