6300 attenuator lack questions

  • 1
  • Question
  • Updated 3 years ago
  • Answered
  • (Edited)

during these summer nights I had more time to do some listening on low bands, mostly on 40 and 80 meters. In a A/B comparison with another Stars and Stripes rig I realized that the use of attenuator could help a lot in the "noise handling battle".
So I am wondering if, in next SSDR releases, 2.0 or higher, also a 6300 rig can have a 10 db attenuator or if are there any technical issues that justify this feature lack.
I have a work-around for this: usually I reduce the AGC- threshold and add AF gain but I don't know if it could be better with a fixed attenuated signal.
Could 6500 and 6700 owners tell about their experience?

Thank you very much and 73
Photo of IW7DMH, Enzo

IW7DMH, Enzo

  • 356 Posts
  • 87 Reply Likes

Posted 3 years ago

  • 1
Photo of Rob Blackie

Rob Blackie

  • 122 Posts
  • 8 Reply Likes
I agree, a straight forward attenuator would be handy, the suggested AGC works to  a point but yes you are right :)
Photo of Les Tucker K6ZF

Les Tucker K6ZF

  • 7 Posts
  • 0 Reply Likes
Enzo, Have you tried to move the RF Gain slider control to the far left position?  Go to the ANT option on the far left side of SSDR and click at the "0" position for a Minus 10 Db gain in the RF level.  This works well on my 6700 station.

Les - K6ZF
Photo of Ken - NM9P

Ken - NM9P

  • 4239 Posts
  • 1351 Reply Likes
I have a 6500 and seldom need any attenuation on 160-40 meters. I do use 10 dB gain above 20 meters and 20 dB at 6 meters. All the attenuation would do is lower the noise floor and prevent overloading the receiver, which NEVER happens at my station. Setting the AGC-T has the same effect for me.

I thought, however, that the 6300 did have attenuation, as Les K6ZF described. I know that currently the 6300 preamp is actually gain-contoured so that at lower frequencies it doesn't actually provide any gain. (In order to protect the 6300 front end.)
Photo of KM6CQ - Dan

KM6CQ - Dan

  • 184 Posts
  • 37 Reply Likes
At my location with a full wave loop, on my 6500 I use 10 db attenuation below 20 meters at night. I adjust the AGC-T so the noise floor does not trigger it. This makes for much less listening fatigue because, it keeps the band noise to a minimum between dits and dahs and words.  
I would prefer a 3 step attenuator in 6db increments.

73,   Dan KM6CQ
Photo of HCampbell  WB4IVF

HCampbell WB4IVF

  • 296 Posts
  • 95 Reply Likes

You could use an external step attenuator (MFJ-762, etc.) along with an antenna interface (such as the DXE RTR-1A).  The RTR-1A has other uses, such as letting you add a receive antenna to the 6300. 

Photo of Rob Fissel

Rob Fissel

  • 270 Posts
  • 48 Reply Likes
FWIW, the transverter port on the 6300 makes a fine RX antenna port, which I use with my RF PRO-1B loop. I use the same keying relay as the amp, daisy chained together, to switch the preamplifier off during TX. 
Photo of IW7DMH, Enzo

IW7DMH, Enzo

  • 356 Posts
  • 87 Reply Likes
Thank you very much for your feedback.
I found that 0 db antenna gain is not enough, here in Europe, for 40 and 80 meters. That was the reason I asked for a -10 o -20 db attenuator.
Actually I don't like very much the idea of an external step attenuator, I would prefer a software extension of 6300 firmware. I could pay for this enhancement and that is the reason I asked for it in SSDR 2.0 or later version.
I hope Flex designers will provide a "pay-for-feature" in their next software.

73' Enzo
Photo of EA4GLI - 8P9EH - Salvador

EA4GLI - 8P9EH - Salvador

  • 1782 Posts
  • 547 Reply Likes
Hi Enzo, I thought that on the 6300 the slider to the right on the ANT Gain actually is an ATTENUATOR on 40, 60, 75, 80 and 160m. Let me see if I find a reference on the manual....
Photo of EA4GLI - 8P9EH - Salvador

EA4GLI - 8P9EH - Salvador

  • 1782 Posts
  • 547 Reply Likes
Here we go, on the Manual for Ver 1.6.21 is on pag. 96.