Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
4K DIGU Slice but TX Suppressed above 2.6K??
Options
Dwayne_AB6A
Member ✭✭
Working with a WSJT-X and a DIGU Slice opened up to 4K. I find that Transmit is suppressed above around 2.6K? Setting XMIT frequency at the upper ends of the slice and MOX is enabled but AMP shows no signal from radio. As I move the XMIT frequency back down below 2.6K I get a few watts before it jumps to full power from the radio.
0
Answers
-
Will using "Fake It" in WSJT-X solve the problem for you?
0 -
Two possible causes. Your TX bandwidth is to narrow. Or you are not running in Fake it/Rig mode in WSJT.
Change TX bandwidth in SSDR.(watch TX bandwidth on 60m)
Change to fake it in wsjt under File, settings Radio(not for 60m)
0 -
You have your transmit bandwidth set too narrow. It is on the Transmit Control panel, a pair of text boxes with up/down arrows at either end. Set the "High Cut" to 4kHz.
1 -
Awesome! I changed settings in WSJT-X to rig control, but I was not aware of the TX band settings... Under PHNE Settings correct in 3.1.8??0
Leave a Comment
Categories
- All Categories
- 246 Community Topics
- 2.1K New Ideas
- 489 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 223 SmartSDR CAT
- 163 DAX
- 348 SmartSDR API
- 8.6K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 766 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 733 Genius Products
- 393 Power Genius XL Amplifier
- 255 Tuner Genius XL
- 85 Antenna Genius
- 229 Shack Infrastructure
- 153 Networking
- 370 Remote Operation (SmartLink)
- 120 Contesting
- 583 Peripherals & Station Integration
- 115 Amateur Radio Interests
- 813 Third-Party Software