Conversations

Conversations 121 - 140 of 142
Photo of Steven G1XOW
3Dconnexion SpaceNavigator Mouse on Felx 6k series?
Hi all, Has anyone connected the 3Dconnexion "SpaceNavigator" Mouse with SmartSDR / 6k. I have just purchased one of these, and it works ...
  • 1 me too
  • 3 replies
  • Question
Photo of KY6LA - Howard
Amateur Radio Parity Act New Video
The Homeland Security Department brokered the beginning of the Amateur Radio Parity Act legislation initiative in Congress in conjunctio...
  • 3 me toos
  • 8 replies
  • Praise
Photo of Steven G1XOW
SSDR receive filter passband ?
I really miss the ability to customize the receive passband filters like I could in pSDR! Is there any way to permanently change or stor...
  • 11 me toos
  • 5 replies
  • Question
Photo of James Bondo
6300 will not transmit sub on 60 meters
Running win7 and 1.5.1.152 and 6300 will not transmit via ptt or vox on 60 meters. In cw mode I get a carrier when the tune button is eng...
  • 1 me too
  • 5 replies
  • Problem
  • Solved
Photo of Steven G1XOW
BANDPLAN MODE PROBLEM?
Hi, I'm using Ssdr 1.5.1 and F6300, sCAT, along with DDUL V3 and latest HRD logbook/cluster. When I click a 40m spot on say 7.122MHz (t...
  • 1 me too
  • 1 reply
  • Problem
  • Solved
Photo of Mike
How long should the radio and SDR take to "find" each other?
The past couple of times (and the current turn on sequence) the front LED is blinking for over 3 minutes and the radio and and SDR haven'...
  • 1 me too
  • 14 replies
  • Question
  • Answered
Photo of Steven G1XOW
MSG: Cannot change antenna while transmitting?
Hi Flexers, F6300 with v1.51 SSDR, DDutil Yesterday I saw a very odd message that has never appeared before. I think it was from eithe...
  • 1 me too
  • 3 replies
  • Question
Photo of Larry Loen  WO7R
Very slow boot of the 6300 on 1.5
Since installing Power SDR 1.5 on my 6300, I have experienced very long boot times.  Sometimes, it never finishes (or I give up after 5 m...
  • 2 me toos
  • 3 replies
  • Question
  • Answered
Photo of Bob Craig, K8RC
Unbundling CAT?
Are their any plans to unbundle CAT from an installation? My logging program now communicates with the radio through IP and there is no ...
  • 2 me toos
  • 6 replies
  • Question
  • Answered
Photo of Mike
6300 and AM broadcast band
I was trying to listen to the local AM station on 1400 Khz to catch the end of a College football game.  It did not appear that the 6300 ...
  • 1 me too
  • 9 replies
  • Question
  • Answered
Photo of Steven G1XOW
F6300 unstable LF carrier?
Hi, looking for other peoples check/feedback please. I know I should not expect too much from the F6 series below 1MHz, but I have found...
  • 1 me too
  • 5 replies
  • Question
Photo of Steven G1XOW
F6300 unstable LF carrier?
Hi, looking for other peoples check/feedback please. I know I should not expect too much from the F6 series below 1MHz, but I have found...
  • 1 me too
  • 2 replies
  • Question
Photo of Gary L. Robinson
Noise Blankers ...
I have always had pretty good luck with the regular noise blanker in SmartSDR and amazed how well it works with many noises without degra...
  • 3 me toos
  • 10 replies
  • Praise
Photo of Steven G1XOW
Outbound Internet access from Smartsdr?
Started SmartSDR 1.51 this morning and my Internet security software pops up asking me to allow outbound internet access from SmartSDR to...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Bill Carnett
flex control
Not sure what's wrong.  When I upgraded to the 1.5.1 a couple of weeks ago, the Flexcontrol started working again.  Today turned on rig, ...
  • 1 me too
  • 5 replies
  • Question
Photo of Larry , W8LO
Signal?
Anyone have an idea what this is? Is about 30 khz wide with frying and popping like rain drops. On 24/7 and seem to be coming out of t...
  • 2 me toos
  • 5 replies
  • Question
Photo of ai6re
AVLC Automatic Volume Limit Control
Auto Volume Limit Control, AVLC to allow setting the max audio you want so if listening to a weak station a strong station does not come ...
  • 3 me toos
  • 13 replies
  • Idea
Photo of Burch Akin
Strange behavior on 160 and 17 meters using WNB
I tried out the WNB on 160 meters last night.  I always have a very high noise level.  I had the AGC-T set between 5-10 and when I would ...
  • 2 me toos
  • 10 replies
  • Problem
Photo of Steven G1XOW
Minideluxe, Ham Radio Deluxe SSDR CAT on Windows 10?
Has anyone got this working with Windows 10 yet?I tried porting my current SmartSDR+CAT+DAX, Ham Radio Deluxe, Minideluxe to a Windows 10...
  • 1 me too
  • 4 replies
  • Question
Photo of Drax
Make the icons for SmartSDR, CAT, and DAX different colors or images.
They're hard to find at a glance.    And why do CAT and DAX both minimize to the task bar and a tray icon?   They should just be tray ico...
  • 15 me toos
  • 11 replies
  • Question