Conversations

Conversations 1 - 20 of 578
Photo of Stan - VA7NF
Front End Protection
How does the antenna switching work between Transceiver Antenna Port 1, SCU-A RF Input, and SCU-A RX Loop Output? I have the 6700 so th...
  • 1 me too
  • 11 replies
  • Question
  • Answered
Photo of Jeff | VA2SS
USB to Serial compatible cable for FLEXRADIO
I would like to share with all of you that I bought and tested successfully a really cheap (price) USB to serial cable from CableCreation...
  • 2 me toos
  • 7 replies
  • Idea
Photo of Gene - K3GC
Flex 6xxx Fan Replacement
There has been great concern about fan failure and replacement in the fgpa fan speed thread.  That thread has gotten almost impossibly lo...
  • 4 me toos
  • 34 replies
  • Question
  • Answered
Photo of Greg
CW sidetone
Does anyone have any idea when the CW sidetone will be available to monitor via DAX so it can be monitored remotely? 73 Greg AB7R
  • 4 me toos
  • 7 replies
  • Question
Photo of Steve N4LQ
Keeping the 6300 quiet and cool
I bought this laptop cooler at Big Lots for $10 and sat the 6300 on it. The case temp dropped 5 degrees and the internal fan never kicks ...
  • 5 me toos
  • 10 replies
  • Idea
Photo of Jeremy Gilbert KC1JZE
Why does the Flex 6600 need band preselectors?
I’m loving my 6600 - an incredible instrument! As I dig deeper and deeper into the documentation and try to learn the art of SDR signal ...
  • 1 me too
  • 14 replies
  • Question
  • Answered
Photo of Mark WS7M
6600 Fan - Disappointed
Ok, so I sent my 6600 in for the PEN update.When it came back it rebooted continuously.  After looking inside I could hear the fan runnin...
  • 1 me too
  • 23 replies
  • Problem
  • Solved
Photo of Kari Gustafsson SM0HRP
After "Transmit slice not selected" Flex do not follow N1MM in SO2R CW a while
I have got 6700 to play almost 100 % with N1MM with SO2. However, when using Ctrl F1 to switch "F1 CQ.." transmission to other slice N1MM...
  • 1 me too
  • 11 replies
  • Question
Photo of John G3WGV
Meter data duplicated?
For some time I've wanted to put some software damping on the S-meter to stop it bouncing around quite so wildly, so that took me into co...
  • 1 me too
  • 5 replies
  • Question
Photo of Mark Erbaugh
zoom to segment
I tune to a CW frequency (7.030 MHz), and click the little S button to zoom to segment. The panafall zooms to 7.125 to 7.300 and shows th...
  • 1 me too
  • 1 reply
  • Problem
Photo of WQ2H - Jim Poulette
Farallon Cable # 9087 (P4 Dragon to Flex 66XX)
Hi folks - Just wondering if anyone has experience with this cable, and/or if Flex has an alternate. It will be important that I get a Pa...
  • 1 me too
  • 4 replies
  • Question
Photo of Ernest - W4EG
QST Review Comparing the ANAN To Flex-6x00 Radio
My letter to the editor and writer of QST October 2015 edition. Hi Martin(AA6E), Regarding: QST October 2015 Edition Product: Apache La...
  • 1 me too
  • 10 replies
  • Praise
Photo of William Hemmingsen
Android App
I started working on a Android App to go alongside my CMD micro.  I wanted a few additional feature at hands reach without having to use ...
  • 15 me toos
  • 74 replies
  • Idea
  • Not Planned
Photo of Paul
DAX IQ bandwidth only 170kHz when set to 192kHz
I currently use DAX IQ to stream 20m to my WebSDR server. Unfortunately when set to 192kHz sample rate, the visible bandwidth is only 170...
  • 1 me too
  • 8 replies
  • Question
Photo of Paul,  KB3ML
S meter with version 2.3.7
After installing Version 2.3.7 in my 6600M, the S Meter and pan display is out of calibration.   Ex:  a -62dbm on the pan display shows a...
  • 2 me toos
  • 15 replies
  • Problem
  • Solved
Photo of WX7Y
S meter still not correct on FLEX6600M with Version 2.3.9
On Version 2.3.9 the S Meter and Pre-Amp is NOT working correctly. On the 6600M to see what I am saying, terminate the Antenna and go to ...
  • 1 me too
  • 2 replies
  • Problem
  • Solved
Photo of Spencer Borden
WSJT No RF
This has been asked so many times, but.... WSJT decodes fine, passes CAT test, DAX is selected in mike profile, level is mid way, (WSJT v...
  • 1 me too
  • 14 replies
  • Question
Photo of Tom Teague
Heatsinks are falling off in 6400 and 6600 models.
As part of the Product Enhancement Notification (PEN) or Recall.  If you want to know where to look to see if both of your heatsinks are ...
  • 4 me toos
  • 48 replies
  • Problem
  • In Progress
Photo of Terry AB2UE
Do FlexRadio service technicians use 'floating or grounded [negative]' output, 13.8VDC power supplies when bench testing radios ?
  • 1 me too
  • 6 replies
  • Question
Photo of James Nelson
Succesful 6000 Power On/Standby Control on the Lan Solution with WeMo
Applying the open collector voltage as Steve N5AC advised then a small relay means an iOS or Android app with a Belkin "WeMo" IP switch &...
  • 5 me toos
  • 28 replies
  • Idea