Conversations

Conversations 1 - 20 of 22
Photo of rjguidrysr
New Maestro loading error 152
New out the box Maestro on the same network and or directly connected to Flex 6600 gives me loading error 152 communication problem with ...
  • 1 me too
  • 6 replies
  • Problem
Photo of N9VC
Maestro Sidetone Volume
Hi Tim, Is there a way to tame down the sidetone volume of the Maestro? Switching between the computer and the Maestro blows out the ear...
  • 2 me toos
  • 2 replies
  • Problem
  • Not a Problem
Photo of Ken W6XB
No N1MM CWX local side tone
I am using SmartSDR V2.2.8 in conjunction with N1MM.  The Flex CWX works great with local CW side tone.  However, when using N1MM with th...
  • 5 me toos
  • 6 replies
  • Question
Photo of Sergey Abrikosov
Radiosport Headphones connection
I ordered 6600+Maestro last week and wonder about adapter cable for Radiosport RS60CF. What are advantage/disadvantage to connect Headpho...
  • 1 me too
  • 6 replies
  • Question
Photo of Chris de Voogd
New heatsinks not touching chip surface and fall of again.
I executed the heatsink modification according instructions. The 2 old ones were both lying on the bottom. Then I glued the new one...
  • 1 me too
  • 8 replies
  • Problem
Photo of Stan - VA7NF
Followup questions: Using N1MM+, Maestro, and 6x00
An optimum contesting arrangement is using N1MM+ for recorded messages (CW or Phone), a Maestro/Keyboard/Mouse/Paddle at the operating st...
  • 1 me too
  • 1 reply
  • Question
Photo of K1UO - Larry
Maestro, N1MM and monitoring of N1MM Function macros...
Was finally able, thanks to various inputs from the many Community contributors, to get N1MM+, Maestro and CW Skimmer all talking nicely ...
  • 2 me toos
  • 2 replies
  • Question
Photo of Mark - WS7M
SPE 2K-FA can TX power end up going out the S02R port
Does anybody happen to know if it is possible for radio TX power to end up going out the SO2R port on the SPE-2K-FA amp? I have two radi...
  • 1 me too
  • 3 replies
  • Question
Photo of KK9W - Steve
Error on Maestro Screen
Been getting this error on Maestro . . . Any Ideas
  • 1 me too
  • 9 replies
  • Problem
  • In Progress
Photo of Barry Young
6400 Issues with Transmitting
I am having a problem with my 6400 transmitting. I can tune the radio just fine via the tune button in SDR. But when I attempt to transm...
  • 1 me too
  • 5 replies
  • Question
Photo of Barry Young
No Audio From 6400
NewBe to Flex Radio...  Setting up Radio. I was hearing audio when I first setup the 6400, but now it has gone silent / like muted.   I h...
  • 2 me toos
  • 16 replies
  • Question
Photo of Thurman Roberson
Dax drivers
Windows update killed dax drivers uninstall and re-install 3 times now with no success any help will be appreciated
  • 1 me too
  • 10 replies
  • Problem
Photo of Mark WS7M
PEN Heat Sink Replacement document
Like I posted humorously in the other post I managed to cut my replacement instructions in half.  Is the PEN heat sink replacement docume...
  • 1 me too
  • 1 reply
  • Question
Photo of Hugo Escalante
Turning On/Off 6600 Remotely
I brought this (AC/DC Power Relay with Protection & De-Bounce. Screw Terminals. 120V Trigger Input) Anyone have a wire diagram, idiot pr...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Juan TG9AJR
FlexRadio TOP Level
Despite the issues with the heat sinks of the new Flex Signature Series and in my particular case with my Flex 6600 that I discover one o...
  • 2 me toos
  • 5 replies
  • Praise
Photo of Mike va3mw
Remote Maestro
All you new Maestro users.  You do know once you have a VPN solution - either via Flex once it is integrated or some other VPN, that you ...
  • 1 me too
  • 3 replies
  • Idea
Photo of John Kludt
The Importance of The Manuals
I was once accused of not being a "real ham" because I have always read the manuals for my equipment.  I started with Flex with a 1500 an...
  • 8 me toos
  • 16 replies
  • Praise
Photo of rjguidrysr
Winkeyer inout on AUX conn pin 4 no keying voltage
New 6600 so might be just op error. CW ok with Paddle input but AUX pin 4 per Hardware and SmartSDR said it is enabled all the time.  PTT...
  • 1 me too
  • 5 replies
  • Question
Photo of bahillen
New Flex6600 and WSJT-X multiple instances and multi Instances JTAlertX on SmartSDR
I received my Flex6600 last week Feb 1, 2018. My first SDR. I have learned a lot about The navigation, setup and use but still have a lon...
  • 1 me too
  • 3 replies
  • Idea
Photo of M Evans
Microphone location /connection
I've spent several days now with my new 6400 and the only complaint so far is the location/type of the microphone connections. Can't use...
  • 1 me too
  • 5 replies
  • Problem