Conversations

Conversations 1 - 20 of 334
Photo of Ray
Stuck in update mode
Tried to update my 6600M to 2.4.9 and it never completed the display just showed the 2 s meters and the power button was solid purple. We...
  • 3 me toos
  • 14 replies
  • Problem
Photo of Rich McCabe
6600 (non M) wont boot
Went to fire up the 6600 this morning and  ended up with a triple red flash showing it wont boot. Tried holding in the power button until...
  • 1 me too
  • 27 replies
  • Question
Photo of Andrew O'Brien
SmartSDR and CW Skimmer frequencies not in sync
Running latest versions of SmartSDR and SDR Bridge, the radio does not follow clicks on the skimmer , Any suggestions?  Andy K3UK
  • 1 me too
  • 25 replies
  • Question
  • Answered
Photo of Bill Garfield W1BG
6600M TX Monitor Not Working when VOX enabled
When operating VOX with either the 6600M (or 6600) I notice that the TX Monitor function cannot be used.  We confirmed this on both the 6...
  • 1 me too
  • 9 replies
  • Question
Photo of Wayne
WWV shutdown annonunced
So WWV is ending service but a feature of the new rigs and firmware/software is accurate freq calibration. So is flex going to provide an...
  • 1 me too
  • 19 replies
  • Question
Photo of Geoff - W8GNM
6600M bandwidth center/width controls
When the 6600M front panel filter controls are put into the "width / center" mode, the filter bandwidth collapses to zero bandwidth if th...
  • 1 me too
  • 7 replies
  • Problem
Photo of David Decoons wo2x
Customize RX filters (right click & configure)
Hi All,I was talking to the guys from Flex this weekend at the ARRL Centennial convention the subject was brought up about future ability...
  • 39 me toos
  • 27 replies
  • Idea
Photo of Rick - W5FCX
Legal Limit Solid State Amp - SPE 2K-FA, KPA-1500 or ??
Looking at solid state legal limit amps with integrated tuner for use with 6700. The SPE 2K-FA and recently introduced Elecraft KPA-1500 ...
  • 2 me toos
  • 30 replies
  • Question
  • Answered
Photo of John-KC2QMA
Show Us Your FlexRadio In Your Shack
I thought it might be fun to have us Flex users show a picture of their FlexRadio in their shack. Here is my 6600M in my shack. It's i...
  • 8 me toos
  • 64 replies
  • Praise
Photo of Rej va2am
6600(m) cw mode memory buffer
6600(M) stand alone, can we store short cw messages like Call 599 report for dx? or do we need to install a third party software? Thank...
  • 1 me too
  • 7 replies
  • Question
Photo of WH6HI - Pat
New Flexradio web Page
New Flexradio Web Page has appeared which is very slick and professional.  Only thing I see that should be fixed is to put the link to th...
  • 1 me too
  • 3 replies
  • Praise
Photo of K1DBO
Slice Master 6000 v0.9.0 beta release
Every new program needs an exciting name... how does Slice Master 6000 sound to you?  Yeah, that's what I thought, too. I was playing wi...
  • 2 me toos
  • 27 replies
  • Idea
Photo of Rich McCabe
AMP TX delay setting for new LA-1K
I just took delivery on a new Palstar LA-1K amp.  I remember reading somewhere that HRO had some recommended TX delay settings and I thou...
  • 1 me too
  • 12 replies
  • Question
Photo of Jon - KF2E
Dead Ethernet Port
Two days ago I turned on my radio and it never showed up in SSDR. I did a little troubleshooting and found I had no lights on the etherne...
  • 1 me too
  • 12 replies
  • Question
  • Answered
Photo of Tim - W4TME
Welcome Neal K3NC as the newest member of the FlexRadio team
I’d like to take this opportunity to welcome Neal Campbell, K3NC as our newest FlexRadio employee.  Neal was an original SDR-1000 owner a...
  • 8 me toos
  • 19 replies
  • Praise
Photo of Rich McCabe
Power off persistance
For some reason my 6600 is not always retaining the settings when it s powered off.  Its not all the time but often. Not a big deal as I ...
  • 1 me too
  • 8 replies
  • Question
  • Answered
Photo of Dennis ODell
Flex 6400M noise floor
My new 6400M has a -120dBm noise floor which equates to a constant S4 on the S meter with a terminated antenna input on 80M and 0dB gain....
  • 1 me too
  • 14 replies
  • Question
  • Answered
Photo of Neil   N4FN
PEN Heat sink replacement
What a classy company. My kit arrived on Friday and it took longer to remove the 14 Torx screws than the update took. I followed the inst...
  • 1 me too
  • 9 replies
  • Praise
Photo of Jean Drolet
Screensaver
Fonction for screensaver for the Maestro and the new 6400M and 6600M
  • 4 me toos
  • 10 replies
  • Idea
  • Under Consideration
Photo of Peter Woodmansee WB6POT
Error connecting to SmartLink Service
Good Morning, Everything was working last night, but this morning I received this message when trying to run the SmartSDR iOS app. I als...
  • 3 me toos
  • 14 replies
  • Question