S Meter Reading after Service
My Open Response to Flex Service Survey The service agent was great in communication via email on the updated on my repair and also show...
Ned K1NJ
Joined on August 4, 2013
83
Likes received
10
Conversations posted
312
Replies posted
245
Conversations followed
Conversations
Conversations 1 - 20 of 41
No audio from Bluetooth headset using PC Remote
Hi guys.. sorry if this is a newbie problem, but I'm trying to use a Bluetooth headset connected to a Surface 3 via PC remote. The heads...
Windows 10 update #1709
Three separate occurrences of the very large Windows 10 Creators update #1709 breaks the DAX drivers. One system running v1 SmartSDR and ...
RFI after transmitting
I have this issue that is driving me bonkers. Everytime after I unkey my mic I get three bursts of RFI each lasting approximately a secon...
Update to 1.10.16 fails. Tried the instructions in the release notes and now my radio is a BRICK
I read the release notes before I tried to update the radio from 1.9.13 to 1.10.16 and saw the instructions about what to do "on rare occ...
_large.png)
profile not loading from cold-start
Hi, I recently replaced my 6300 with a 6500. Since then I have noticed that sometimes when I start the radio from cold it randomly fails...
Receive antenna locked in loop input mode
This is a further update to my post from yesterday on the receive antenna being locked in the loop input mode. The problem occurs on all ...
TX delay missing on 1.9.13
There seems to be a problem with TX Delay settings on 1.9.13 (and not sure how far back) perhaps this is by design or.... Nick GM4OGI bl...
RF Feedback at 10 W locks TX in Tune Position Requiring Tap of the Keyboard Space Bar to Clear
This evening after rearranging my Flex6500, AL811H, and PALSTAR HF Auto, I experienced the unique condition of RF Feedback (I think) that...
Still getting CW issues with internal winkeyer and 1.8
The release notes of 1.8 say that the missing CW sidetone issue is fixed but I didn't see any mention of occasional missing 'dits' from t...
Windows 10 Update Strikes Again!
OK I'll take one for the team! Beware! Microsoft strikes again with their latest Windows 10 Update today (8/4/2016)! This time it's ...
SmartSDR CAT will not open
New Flex 6500 installation with version 1.8.3 of SmartSDR and SmartSDR CAT on a Win 10 PC. Maybe I did something out of order because Sm...
Frequency Display "trimmed"
Flex 6300, Win 8.1, Ver 1.38 The top ten percent of my flag frequency display is cut off. Didn't notice this in ver 1.3. Perhaps some se...
noise blanker nb
Noise blanker is still so so performance
Display Driver Has Stopped Responding and has Recovered
Installed SmartSDR on Surface Pro 3 I5. receiving this message [bottom right]. Screen freezes just before the message. Happens when SSDR ...
Dirty distorted transmit signal
After upgrading to v1.5 my carrier (tune) signal is very distorted and when transmitting audio i'm seeing audio on both side-bands on the...
No sound remote audio after conversion from 8.1 to win 10
Just converted a one year old Windows 8.1 Asus laptop to Windows 10. Conversion went very well, accept now I do not get any sound from t...
WSJT-X caution
K1JT Advises WSJT-X Users Not to Use “Unauthorized” Builds of His Software
TAGS:
Laureate Joe Taylor, new mode, WSJT software su...
Flex 6700 CW issues during ARRL CW DX Test
I operated the entire arrl dx cw contest this past weekend with the Flex 6700, Latest Release of Smart SDR, N1MM+, and CWX Enabled. Dur...
_large.jpg)
Flex 6300 8 second delay over LAN
Not the worst problem in the world but my laptop has an 8 second delay in what it shows on the panadapter, the power out, the SWR, than ...