Conversations

Photo of Tim - W4TME
Welcome Neal K3NC as the newest member of the FlexRadio team
I’d like to take this opportunity to welcome Neal Campbell, K3NC as our newest FlexRadio employee.  Neal was an original SDR-1000 owner a...
  • 8 me toos
  • 19 replies
  • Praise
Photo of Mark K5XH
New Installation problem
Got my new 6600 yesterday! Had it all hooked up within about 30 minutes of getting home last night. But I am one of the unfortunate ones ...
  • 1 me too
  • 5 replies
  • Problem
  • Solved
Photo of K3WR - Jim
FLDIGI Transmit Problem
Trying to get FLDIGI to transmit on my new Flex 6400. Using Windows 10 on my laptop. These are the settings I am using and the radio rec...
  • 1 me too
  • 7 replies
  • Question
Photo of Allan
6600M - will not transmit on FT8
Need help. FT8 decodes fine on 6600M , get tones through radio speaker on transmit but no output power.  Have read through the help sugge...
  • 1 me too
  • 6 replies
  • Problem
  • Acknowledged
Photo of Mark K5XH
Comment on Flex service
A tip of my hat to the service folks at Flex. Thanks to Katie Gartman and Steve Hicks for handling the quick repair of my 6600! CW signal...
  • 2 me toos
  • 2 replies
  • Praise
Photo of Ria - N2RJ
CQWW SSB 2017 post contest report
Someone who shall remain nameless asked once on the CQ-contest list if anyone had placed in the top 10 single op with a Flex 6000 series ...
  • 7 me toos
  • 22 replies
  • Praise
Photo of Mark K5XH
Question about spectrum display in tune with and without amp
I recently had a report that my RTTY signal was broad and distorted. I figured I was doing something wrong with the new 6600. I wish I ha...
  • 1 me too
  • 4 replies
  • Question
Photo of Mark K5XH
Can I connect my 6600 directly to my computer?
Can I connect my 6600 directly to my computer with a normal CAT5 cable? I am having a strange problem and I would like to eliminate the r...
  • 1 me too
  • 4 replies
  • Question
Photo of W5AP
RTTY tones mark 1275 how to adjust hi/low cuts???
Unable to get output when the rtty tones are changed from the default 2125 to 1275. So some have posted this problem before, but no exact...
  • 1 me too
  • 10 replies
  • Problem
  • Solved
Photo of Mark K5XH
CAT won't connect
Hi everyone,I just got a new W10 Pro computer from Neal Campbell to replace my old computer that was running W7 Pro. The old computer had...
  • 1 me too
  • 4 replies
  • Problem
  • Solved
Photo of Mark K5XH
Windows 7 question
I posted an earlier post about having a problem installing the software for my new 6600. The problem was that I had abandoned W10 and pu...
  • 1 me too
  • 6 replies
  • Question
  • Answered
Photo of Bill Billingsley
Received Shipping Notice
20 May 17 Ordered 6600M at Dayton  19 Jan 18  Paid invoice 05 Feb 18  Changed order to a 6600 12 Feb 18  Received Shipping notice FOR THE...
  • 2 me toos
  • 3 replies
  • Praise
Photo of VE7ATJ
Windows strikes again -- latest cumulative update KB4056892 weirdness
Well that was weird.... The Flex 6500 was working fine (except for some problems connecting over the Internet -- see other thread) and th...
  • 1 me too
  • 11 replies
  • Problem
  • Solved
Photo of Mark K5XH
Question about PGXL, SWR, and power output
Please excuse me from asking if this has already been covered or Flex has not released the specs yet (I can't find them if they have).If ...
  • 1 me too
  • 4 replies
  • Question
Photo of Steve - N4TTY
ARRL RTTY RU Contest 2018
Just a little less than 24 hours until the contest begins and I'm not going to be participating. I picked the "Conversation Type" as "Pr...
  • 1 me too
  • 1 reply
  • Question
  • Doesn't Need an Answer
Photo of Jerry Gardner
wsjt-x 1.8.0 Transmission Timing Problem?
I'm using wsjt-x 1.8.0 on a Flex-6500 in FT8 mode. I've noticed that the rig doesn't start actually transmitting until several seconds in...
  • 1 me too
  • 14 replies
  • Problem
Photo of Bill -VA3WTB
Thanks Flex
Thank you Dudley for helping me over the phone. Thank you Katie for looking after the shipping details. Thank you Greta for doing the rep...
  • 3 me toos
  • 5 replies
  • Praise