SmartSDR 2.5?
Congratulations, Team Flex on the launch of SmartSDR 3.0. Will download instructions for SSDR 2.5.x be along shortly?
Mark - W3II
Joined on July 8, 2014
33
Likes received
11
Conversations posted
139
Replies posted
77
Conversations followed
Conversations
Conversations 1 - 20 of 43
v 3.0.19 Why doesn ́t API.RadioList(0).RFPower show any output power any more?
v 3.0.19 I have a visual basic app where I want to display the RF
power, frequency used and other parameters.. All works fine after up...
Trying to Using two pc win 10 with SmartLink from the same IP address ??
I am able to login from both pc, local and remote one at a time or one local and one remote. But never can log them both at the same time...
WSJT-X 1.9 Power drops off past 2500 Hz
I'm sure I have a setting wrong somewhere , Using Flex 6600 , ssdr V 2.3.9 , WSJT-X V 1.9.1 . I noticed today when moving the Red goal po...
SmartSDR with an "M" model radio
Can anyone tell me the sequence of commands sent by SmartSDR (via the API) when it is started using an "M" model radio. Apparently, the ...
Turn off/on the DAX TX Stream
Is there any way to programmatically turn the DAX TX Stream (TX button) off and on?
After upgrade cant get CAT control with WSJT-X
After upgrading to 2.3.7 I can not seem to get WSJT-X set up to do FT8 anymore. I've tried to reconfigure per community instructions but ...
spot display with ssdr 2.3.7
I have installed ssdr 2.3.7 with no problems on my 6500. I run DXsuite with spot collector installed. Spots are enabled, "display calls ...
PGXL wireshark dump
Hi all of you lucky new PGXL amp owners... I am wondering if any of you would be willing to send me a wireshark dump of PGXL communicati...
fr stack causes relay chatter when active radio slice enable TX is enabled
with two slices open in myu Flex 6500 if I enable "active radio slice enable TX there will frequently (not always) be a rapid relay chatt...
Stacks for Flex
Noticed that when I use Stacks for flex and I have "active radio slice enable tx" enabled when I switch bands the TX select will switch f...
what am i doing wrong
hi all,hope someone can help me,i have v2 installed on my main computer and wish to install it on my laptopthe problem i have is i have d...
FRStack user manual for newbie?
I should be receiving my first Flex 6x00 radio this week, and have started reading to learn. I came across the FRStack utility software, ...
FRStack Radio Chooser "There are currently no radios available"
I recently installed SRStack 2.1.30.9 on a computer and it did not find the Flex-6700 (through SmartLink). SmartSDR Cat v2.1.33 works fi...
SmartLink access details for my client app
I've been writing my own client app for the Flex Radio for quite some time. I'm fairly close to completion but have a few more features ...
_large.jpeg)
DD6xxxx Macro command for power level adjustment
I can't seem to find this macro? Can anyone crack the code? TIA 73
How do I get SSDR CAT to go to COM4 to use with N1MM Logger+?
Just had to re-install SSDR and CAT assigned a COM49 port which N1MM can't find. How do I get it back to Com 4 where it used to be? Thank...
FT8 not operating on all bands.
I have been using WSJTX's FT8 for the last week on my Flex 6500 running Smart SDR v2.0.19.98. Had some initial issues with DAX so I relo...
Bit cable
I got an FTDI C232HM-EDHSL-0 cable and I have two problems with 6500 , SSDR last version. 1 - It works very well as BCD, selecting Bit c...
KeepAlive() change request in the api
In radio.cs, the KeepAlive() function has an if block to check if: if (!API.ProgramName.Contains("Maestro")) Any chance that can be cha...