Conversations

Photo of Richard Saue
Windows 10 november update 1511 broke DAX...
I did the Win 10 november update tonight. That broke my CAT ports and DAX drivers. Uninstalled SmartSDR 1.5.1, and made a new install. No...
  • 2 me toos
  • 34 replies
  • Problem
  • Solved
Photo of Bob Wright, N7ZO
Make “quick select” modes persistent per band
In the latest software manual, section 8.4, page 30, it explains how to set the three quick select mode buttons that always show next to...
  • 2 me toos
  • 1 reply
  • Idea
Photo of Roy - W5TKZ
FlexControl will not connect -- Windows 10
Flex 6300, Win 7 & 10, Ver 1.4.16.142 When I cold boot to begin operating, the FlexControl does not work. I have found a work around by g...
  • 3 me toos
  • 9 replies
  • Problem
  • In Progress
Photo of Bill Turner
How best to set RTTY drive level
Running a 6300 with SmartSDR.  My amplifier needs about 40 watts of drive for RTTY. There seem to be two ways to set drive to this level ...
  • 1 me too
  • 2 replies
  • Question
Photo of Joseph Duerbusch
No Power Output
No Power Output, all bands all modes. I have a 6300 bought in December 2014. software v1.4.3.55, it has been working very well until last...
  • 1 me too
  • 3 replies
  • Problem
  • In Progress
Photo of Joseph Duerbusch
Message saying it was going to downgrade?
I have a Flex 6300 and I upgraded to  1.4.3.55 V this week.  All worked fine.  Enjoy having the Monitor on for RTTY. But this morning whe...
  • 1 me too
  • 3 replies
  • Problem
  • Not a Problem
Photo of Joseph Duerbusch
Smart S-Meter Problem
I am trying to use the Smart S-Meter with my Flex-6300. It works fine by it self, it uses the CAT port 4.  But if I open up Writelog, I g...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Keith Morrison
Flex 6300 & MMTTY
Can anyone solve my problem with MMTTY.... everything is fine until I narrow the RX filter down to say 300 Hz then the 2 vertical lines d...
  • 1 me too
  • 2 replies
  • Question
Photo of Joseph Duerbusch
Heil HM-12 Mike adjustment 6300
New Kid here, I am using a Heil HM-12 Mike on my Flex-6300, same mike as I used on my Flex-3000.  No problem, but would like to know the ...
  • 1 me too
  • 2 replies
  • Question
Photo of Joseph Duerbusch
DAX Problem setting up DAX Audio RX/TX
I have been unable to setup the 2nd DAX channel of receive and transmit. on channel one I  have: DAX Audio TX 1 DAX Audio RX 1 Works fine...
  • Joseph Duerbusch, 4 years ago

  • 1 me too
  • 0 replies
  • Question
Photo of Kevin J. Mahoney
little power
I am sure that I am missing something very simple. Turned on my 6300 today, receive was fine but when I hit "tune" to check my external a...
  • 3 me toos
  • 3 replies
  • Problem
  • In Progress
Photo of Joseph Duerbusch
Network+switch Which should I buy?
I ordered a 6300 today and need to buy a network switch so I can use the single network cable in the shack.  I wonder if anyone had a rec...
  • 1 me too
  • 7 replies
  • Question