Conversations

Conversations 1 - 20 of 32
Photo of Al Reeves
Microphone Recommendation
I  recently purchased a Flex 6300 and I'm looking for recommendations from others as to the best microphone to use.  I have tried the Hei...
  • 1 me too
  • 17 replies
  • Question
  • Answered
Photo of Jay Spaulding
Mox button Dont work
Smart SDR V2.0. I tried to use the MOX button a couple of times while not in remote cause I'm sitting at my desk right next to the Flex a...
  • 1 me too
  • 5 replies
  • Problem
  • Not a Problem
Photo of Chris DL5NAM
... same procedure as last update?
... only run the update, restart PC and again the old bug is here again at every SSDR start!
  • 1 me too
  • 9 replies
  • Problem
Photo of IK6DLK Fabrizio
Error at the start of SliceMaster v0.10.4c
SliceMaster v0.10.4c
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Gene - K3GC
spot display with ssdr 2.3.7
I have installed ssdr 2.3.7 with no problems on my 6500.  I run DXsuite with spot collector installed. Spots are enabled, "display calls ...
  • 1 me too
  • 14 replies
  • Question
  • Acknowledged
Photo of Jay Spaulding
DAX V2.3.7 Error
I did the update this morning and now my DAX don't work. Shows Error on install. I tried multiple times. Even did it manual. Still dont w...
  • 1 me too
  • 4 replies
  • Question
Photo of William Hemmingsen
Behringer PL1 midi controller for Flex 6k
I have created an application that allows the Behringer PL-1 DJ midi controller to be used with the flex 6000 series SDR.  This applicati...
  • 4 me toos
  • 18 replies
  • Idea
Photo of Jon - KF2E
WSJT-X configuration problem
I'm trying to get WSJT-X configured on my new 6600. I have version 2.1.33.106 of SSDR and version 1.8.0 r8193 of WSJT-X. When I try to co...
  • 2 me toos
  • 10 replies
  • Problem
  • Solved
Photo of ROBERT WHITE
Behringer CMD MIDI Controller with Flex 6300
I have just purchased a Behringer CMD MIDI Controller to use with my Flex 6300 and need help getting it started. I am running Win10 64 bi...
  • 2 me toos
  • 11 replies
  • Question
Photo of John - K3MA
Connection Issue SmartSDR iOS on iPad
I originally posted in this thread but it was not answered so I have created a new thread. https://community.flexradio.com/flexradio/top...
  • 1 me too
  • 7 replies
  • Question
Photo of N3NER
Warranty transfer problem, not good business.
I have been a LONG time supporter of Flex (many many years) and I have had just about every radio they made.  I recently had a problem wi...
  • 1 me too
  • 11 replies
  • Problem
Photo of Les Brown
Ending a remote session with a 6500 using the Maestro
I am operating my Flex 6500 remotely using the Maestro, which is connected to my LAN by an Ethernet cable. So far, the only way I have fi...
  • 1 me too
  • 6 replies
  • Question
  • Answered
Photo of Trevor-EI2GLB
K9DUR voice keyer can not set up
HI I am trying to get the K9DUR voice keyer set up, no matter what I do I can not get it to accept my PTT serial port settings, it keep s...
  • 1 me too
  • 7 replies
  • Question
  • Answered
Photo of Osiel Rodriguez
Crashed SmartLink Session
I have upgraded to v2 of the SmartSDR software with no issues.  One thing i found is that if the radio software crashes during a remote c...
  • 1 me too
  • 10 replies
  • Problem
  • Acknowledged
Photo of Tico
Tell us your V2 REMOTE CW performance experiences.
Can someone tell us his V2 experience regarding remote cw operating? Till now all our remote attempts with VPN where not completely succe...
  • 2 me toos
  • 10 replies
  • Question
  • Answered
Photo of Mike va3mw
Getting read for SmartLink -- test your upload performance
SmartLink is coming and a number of you are going to want to give a try from Starbucks, your Mother in Laws, etc.  :) This is going to b...
  • 7 me toos
  • 27 replies
  • Idea
Photo of BA7NQ
SmartSDR v2 works great!
Just try SmartSDR v2, it work fine! Easy install and setup without read any manual. I try remote operate my office FLEX-6500 with iPhone ...
  • 9 me toos
  • 10 replies
  • Praise
Photo of Al Reeves
6300 and V2.0 Upgrade is it Worth it??
I'm thinking of upgrading my 6300 V2.0 and want to know if the benefits are worth the $200 cost.  First of all I'm not at all interested ...
  • 1 me too
  • 12 replies
  • Question
  • Answered
Photo of Rick Hadley - W0FG
Can't get SmartLink working, need help.
OK, I give up.  I need some help.  Try as I might, I can not get SmartLink running.  Here's my current configuration:  Netgear DM111 DSL ...
  • 2 me toos
  • 12 replies
  • Problem
  • Solved
Photo of Craig McVeay
Loss of CAT in all applications after installing V2.0?
After installing V2.0 and getting SmartLink setup and running, I was feeling pretty good about this update.  This morning, I sat down, fi...
  • 1 me too
  • 4 replies
  • Question