Conversations

Conversations 1 - 20 of 125
Photo of Gene Duprey
Hi Everyone, I'm a new owner of a CPO 6500 and a Maestro A.
Hi I'm a new owner of a CPO 6500 and Maestro A.  Coming up on 1 week, I ran remote over the weekend and on the last day I found the Maest...
  • 1 me too
  • 6 replies
  • Question
Photo of Hector W2NPR
windows 10 pro updates and SSDR 2.3.9
Greetings All....I am running a Windows 10 pro PC that I acquired this week and connecting to the radio was flawless until the updates st...
  • 1 me too
  • 8 replies
  • Problem
Photo of Stephen Hawkins NG0G
Flex community login problem solved
Difficulties logging in to the Flex community and to open or look at trouble tickets.   I have had  problems logging in both to the Flex ...
  • 2 me toos
  • 7 replies
  • Question
Photo of John Watson
6300 Keying Kenwood TL-922a
I have the 6300 connected to the 922a properly, but when I move the amp to operate, it keys the amp???
  • 1 me too
  • 5 replies
  • Question
Photo of Bob  KN4HH
Experiencing intermittent CAT data flow to/from my Flex 6500
I am using a Flex 6500 to interface with a SPE Expert 1.3K and a AT-Auto tuner.  I am experiencing a condition where after a few minutes ...
  • 1 me too
  • 6 replies
  • Problem
Photo of Mark - WS7M
Figures...
So my 6600 came back from fan replacement 3 months ago.  Since then its been on 24/7.  It has been rebooted a couple times without issues...
  • 1 me too
  • 3 replies
  • Problem
Photo of Hel, OE8TTR
How loud is the 6600?
Hello, being a Flex-6500 user, I'ld like to upgrade for a 6600 BUT before I do this, I'ld like to know about the fan-noise from the 6600....
  • 1 me too
  • 19 replies
  • Question
Photo of Jim Osterling
Distorted audio on 6600
I see the audio thread discussing the 6400 has been closed as solved. I'm not sure if I have the same problem or not. I've had the 6600 ...
  • 2 me toos
  • 12 replies
  • Problem
  • In Progress
Photo of KM6CQ - Dan
Is the 6600 corruptible from power loss?
The idea is simple. I can remotely switch the power to my 12 volt supply. This will cause the radio to turn off. At the same time the Dow...
  • 1 me too
  • 4 replies
  • Question
Photo of Morris Wideman
Work around for FT8 time sync problem with older Flex units
Hello if you have operated FT8 mode with your Flex radio and noticed the decoding has decreased or has problems the longer you operate th...
  • 1 me too
  • 9 replies
  • Idea
Photo of Roger Cooke
Flashing red power switch
I have just received my new Flex 6600. Switched it on with a green flashing light on the power switch. This turned into a flashing red li...
  • 1 me too
  • 9 replies
  • Question
Photo of Dave - G3SBP
Flex 6700 RCA Tx 1 reset on opening by DDUTIl V3
Flex-6700. Use DDUTIL V3 to run HRD Logbook which until recently worked perfectly. Now each time I restart I have to manually go to FLEX/...
  • 2 me toos
  • 10 replies
  • Problem
Photo of Peter Bacon
SmartSDR-iOS default startup band
Whenever I connect to my Flex 6700 using SmartSDR for iOS on my iPad Pro, it always starts up on 20m CW.  Where is the setting so it will...
  • 1 me too
  • 1 reply
  • Question
Photo of Alex - DH2ID
Microsoft has stopped the 1809 update and warned not to install it manually
Quoting MS: "We have paused the rollout of the Windows 10 October 2018 Update (version 1809) for all users as we investigate isolated rep...
  • 1 me too
  • 7 replies
  • Question
Photo of mikeatthebeach .
Tuning wheel in SDR IOS on iPhone changes sensitivity when pressed
When I press the tuning wheel in SDR IOS on the IPhone I notice the receive sensitivity increase when Tuning wheel is pressed or tuned...
  • 1 me too
  • 3 replies
  • Question
Photo of Al Matthews
6600m Hung with 2.49
I upgraded to 2.49, and have been running it for several days. The 6600m has the remote connected to an ip switch. The 6600m had been tur...
  • 1 me too
  • 3 replies
  • Question
Photo of K5XH
Question about VPN
I know nothing about VPNs. When I do a Google search I see that one sets up a VPN to hide their identity and web activity. But I have see...
  • 1 me too
  • 7 replies
  • Question
Photo of Gregory Stobbs
WSJT-X not decoding. I am seeing signals in the WSJT-X waterfall; clock seems accurate
WSJT-X not decoding. I am seeing signals in the WSJT-X waterfall; I can send CQ and getting RF out; the clock seems to be within 0.2 secs...
  • 3 me toos
  • 13 replies
  • Question
Photo of John - K3MA
SmartSDR V2 Display Not Working
See the photo of the Maestro screen.  Last week we had Comcast connect a cable internet service to replace the slow AT&T DSL service.  Wi...
  • 2 me toos
  • 9 replies
  • Question
  • Answered
Photo of Mark K0JM
FlexControl no longer detected
All has been running well for nearly a year, but I had a hard drive crash last week (seemingly unrelated to Flex) and had to restore from...
  • 1 me too
  • 7 replies
  • Problem